Aller au contenu principal

Introduction

Usa questa guida per sostituire o riparare i bottoni sul controller DualShock 4.

  1. Aiutandoti con un giravite Phillips #00, rimuovi le quattro viti da 6.0 mm che fissano la scocca posteriore al controller
    • Aiutandoti con un giravite Phillips #00, rimuovi le quattro viti da 6.0 mm che fissano la scocca posteriore al controller

    • Non forzare troppo le viti mentre le sviti, o potresti danneggiarne la filettatura, rendendone la rimozione impossibile.

    Yo usé un Phillips #000, ya que el #00 quedaba grande y podía dañar el tornillo.

    Adolfo Gomez Toledo - Réponse

  2. Comincia con l'impugnatura sinistra: Per cominciare, afferra l'impugnatura sinistra del controller. Inserisci uno strumento di apertura in plastica all'interno della fuga, e scivola sino agli sticks.
    • Comincia con l'impugnatura sinistra:

    • Per cominciare, afferra l'impugnatura sinistra del controller.

    • Inserisci uno strumento di apertura in plastica all'interno della fuga, e scivola sino agli sticks.

    • Fai leva sullo strumento per continuare a aprire il dispositivo.

    • Ripeti questi passi per l'impugnatura destra.

    Shoulders are where L1/L2/R1/R2 are, not the %#*@ handles. Confusing instructions.

    foxhoundunit89 - Réponse

    Quick tip: Be VERY careful at this step not to dislodge the tiny spring attached to the L2/R2 buttons. While removing the cover, it's easy to pull off either L2/R2 button. Inadvertently pulling off either button will also remove the tiny spring as well. While not too difficult to reassemble, it's not obvious where the spring goes as the spring is almost completely hidden along the side of the button (on the inside).

    I just successfully completed analog stick replacements for two controllers. I completed the first repair without any trouble but managed to dislodge (and almost lose) the spring on the second time around. Needless to say, I spent some time trying to figure out where the spring is supposed to go (no photos of this anywhere). By sheer luck, I figured it out on my own. :)

    Good luck and take your time--especially the first time!

    Michael Whang - Réponse

    couldn't have posted pics for me? :D

    kimsballs -

    Golden tip but I would add a thing or two.

    Most probably both triggers R1&R2 will stay in lower half of the pad case with springs hanging there.

    You must take them of their lower case sockets before assembly and fit them bellow L1&L2

    When you feel click when fitting them and spring works like on normal assembled pad you're done.

    If thats not the case do not try to assemble lower casing half as triggers will not work properly.

    Simon -

    if you lost the springs unfortunately, the triggers would still work but it is harder to get to the precise digital press. In other words you will have hard time to create a light press than a hard press.

    meaningless -

    My controller broke

    Gary - Réponse

    So what I seem to see a lot of sources fail to mention with this model (and promptly break without noticing) are the two plastic tabs attached to the front shell on either side of the headphone jack ; in order to properly pry that section open, all you need to do is lightly push those plastic tabs in, and the section should open up easily. That seems to be one of the main things that prevent people from prying the shell open.

    The updated models have the tabs as well, but aren’t as stubborn considering the bars between the shoulder buttons on those are inside as opposed to being a part of the shell.

    Hope this helps, and feel free to discuss, especially if you’re more familiar with the issue than me.

    Rifter - Réponse

  3. Inserisci uno strumento di apertura in plastica all'interno della fuga, e separa le due scocche in un punto nei pressi di questi bottoni: Tasto Share Tasto Options
    • Inserisci uno strumento di apertura in plastica all'interno della fuga, e separa le due scocche in un punto nei pressi di questi bottoni:

    • Tasto Share

    • Tasto Options

    • Adesso separa i due pezzi che compongono la scocca del controller, tenendo sempre presente che saranno ancora collegate tramite un nastrino da circuito.

    • Spesso tre piccoli pezzi cadono dalla scocca. Per evitare che vadano persi, assicurati di lavorare su di un tavolo ben controllato.

    • 2 Molle dei Trigger

    • 1 Estensione di colore Grigio del Tasto Reset

    You can't just pull the casing halves apart. There is a plastic bar that is part of the casing and separates the L1 and R1 buttons from the L2 and R2 buttons. To get this loose, pull the casing outward perpendicular to the L and R buttons until you can slide the L2 and R2 buttons from behind the plastic bar.

    dzturbd - Réponse

    SO yesterday replaced the thumb stick on my controller, and now the R2 button is stuck, know any way to remedy this?

    ScootsMcgoots -

    I know you put a warning, but I lost the grey reset button extension. Any idea where to get a replacement part?

    miamiman77 - Réponse

    Hey, not even sure when you wrote this, but wanted to share my solution for this problem. I lost one of my reset button rubber pieces when I was doing a different repair, and found that a standard bamboo skewer is just about the perfect diameter to function as a replacement. Just cut it to the proper length and you should be able to get it in there and get your reset functionality back.

    tcbrekke -

    You don't really need it. A long paper clip will work fine.

    Ron Smith - Réponse

    I've removed and changed all buttons all seemed ok but now the options and share button don't work, as in when I pressed them down there is no longer a click (bounce) I'm certain it's back in the correct place and I don't think they can be put the wrong way up, does anyone have any advice please :)

    Rachel - Réponse

    My share button stopped 'clicking'. When I stripped the controller down I noticed a small copper coloured dimple on the motherboard was depressed instead of proud like the one for the options button. With bluetack I was able to pull it out but each time I tested it with my finger it clicked once and stayed depressed. I don't think there is a permanent solution to this as it's probably metal fatigue or similar so i put a tiny bit of blue tack overy the dimple so the plunger could push that bit further and hopefully pull it out each time. Seems to work as I reassemble the controller. Fingers crossed it holds out a while! I'd love to know if someone else had a different solution.

    The5HD -

    I had an extra part, and it wasn’t gray. Thank goodness for the picture of the black one. It’s rubbery. The small end should be inserted down towards the gold colored spot. It’s next to the word RESET on the mobo.

    J Coyote - Réponse

    When reassembling: If, like me, your R2/L2 buttons stayed with the bottom of the controller when you took it apart, it will be impossible to reassemble and get the tiny springs back in place.

    To remedy, remove the buttons, and attach them, with the springs correctly placed, to the top of the controller. There are two tiny grooves, one on the button, and one on the controller top, into which the spring fits.

    Jeff Human - Réponse

    Jeff, we owe you a six pack for this comment.

    James Goldie -

    Thank You!! The spring came out and I looked for a way to reinsert it. So I led a thread through its opening (so it couldn´t jump away), and compressed it with pliers. So it was easy to put it in.

    VauWeh -

    Jeff, you've been a wonderfully helpful Human. Thanks for the ingenious tip.

    Kris W -

    Thanks man i was struggling there

    Shut-_-Up -

    My controller broke

    Gary - Réponse

    Something is stopping me from opening it cause it cut both by splitting tools

    Josuke Higashikata - Réponse

    Mine was also really really resistant to being pried open. In the end, i did my best to loosen the entire gap at least once, then inserted along the middle bottom and used more force than i would have been comfortable with. The plastic on the edges is slightly shot now and it’s not as smooth a grip-feeling anymore, but it came apart fine and I didn’t break anything important. There is just a lot of surface for a friction fit like this and the joysticks keep pulling it back down, which in combination makes it really resilliant. In my case it also was exuberated by a minor soda spill along the right handle which ‘glued’ it together, and i imagine that can also happen just with use and ‘hand cheese’, especially on the outer edges. There is a lot of surface area to stick together there.

    Seleen Shadowpaw -

  4. Stacca il nastrino della scheda madre che connette entrambi le parti della scocca del controller afferrandolo e tirando con le dita. Ricorda l'orientamento del nastrino, perciò assicurati  di reinserirlo nello stesso verso quando  lo riconnetterai. Non appena avrai separato le due metà della scocca, metti pure da parte quella superiore.
    • Stacca il nastrino della scheda madre che connette entrambi le parti della scocca del controller afferrandolo e tirando con le dita.

    • Ricorda l'orientamento del nastrino, perciò assicurati di reinserirlo nello stesso verso quando lo riconnetterai.

    • Non appena avrai separato le due metà della scocca, metti pure da parte quella superiore.

    can you share the battery dimension?

    luxusmirajane - Réponse

  5. Aiutandoti con delle pinzette a becco inclinato, rimuovi il cavetto della batteria  scuotendo leggermente il connettore su entrambi i suoi lati. Dopo che avrai rimosso il connettore dalla scheda madre, la batteria potrà essere rimossa dal controller. Una rimozione brusca e violenta del cavetto della batteria potrebbe deformarne il connettore.
    • Aiutandoti con delle pinzette a becco inclinato, rimuovi il cavetto della batteria scuotendo leggermente il connettore su entrambi i suoi lati.

    • Dopo che avrai rimosso il connettore dalla scheda madre, la batteria potrà essere rimossa dal controller.

    • Una rimozione brusca e violenta del cavetto della batteria potrebbe deformarne il connettore.

    For the replacement battery I found that the Turnigy 2000mAh 1S 1C Lipo w/ 2 Pin JST-PH worked perfectly while also being a budget option at only $2.54 USD before shipping. However ONLY INSTALL AFTER CHANGING THE POLARITY OF THE CONNECTOR, this can be done with a pin or craft knife with relative ease. After doing this the controller has doubled in battery life. It required no modification to the controllers internals only extra care to ensure the longer cables didn’t get pinched in reassembly.

    Ryan - Réponse

    Got the battery detached without warping the plastic grips/ prongs, but it won't stick back to the board on reassembly. Is there an adhesive i should use?

    Ferrum Phoxx - Réponse

    Ferrum Phoxx - Did you just remove the plug from the socket? By that, I mean you didn’t pull the socket it was in off of the board too? If you did pull the socket off as well, I think that would require resoldering the socket to the board first. Tricky, but someone with some soldering experience ought to be able to fix it for you.

    nowurgone - Réponse

    I had trouble with analoge, I fixed that but FPC (flat connector) on mainboard broken and I soldered new 12 pin FPC on mainboard again, but in reverse!

    then I put charging cable and the dualshock did not turn on , and I sensed that the dualshock is heating up, I remove charging cable as soon as possible.

    problem is this : negative and positive putted in reverse.

    I don’t kwow what happen if I solder new FPC in right position .

    Does it work or somethings going to out of service?

    sorry formy poor English language .

    regards,

    Hamed

    hamed1379 - Réponse

    I can’t pull the connector plug out of the socket. I’ve used my fingers, I’ve tried tweezers. I’ve been rocking it for 15 minutes but it won’t come out.

    marcus2159 - Réponse

  6. Rimuovi l'unica vite da 6.0 mm  Phillips che si trova  proprio sotto l'alloggio della batteria con il Giravite Phillips  #00.
    • Rimuovi l'unica vite da 6.0 mm Phillips che si trova proprio sotto l'alloggio della batteria con il Giravite Phillips #00.

    • Non forzare troppo la mano mentre sviti, o romperai la filettatura, rendendo l'estrazione della vite impossibile.

    Hello. I got a new graffiti controller (without hardware) and i wanted to switch my parts in the graffiti one. I have a PS4 Controller. Not a slim. But it seems like my motherboard screw is on the other side.. its on the right side of the motherboard and my graffiti is on the left.. what controller do i need to fix this?

    TheTechnoMan - Réponse

  7. Stacca delicatamente il nastrino del touchpad connesso alla scheda madre aiutandoti con un paio di pinzette a becco inclinato. Il nastrino del touchpad è connesso alla scheda madre mediante un connettore che si piega e si deforma. Per riattaccare il nastrino, la linguetta di plastica dovrà essere delicatamente reinserita nel suo alloggiamento. Stacca delicatamente il nastrino del touchpad connesso alla scheda madre aiutandoti con un paio di pinzette a becco inclinato. Il nastrino del touchpad è connesso alla scheda madre mediante un connettore che si piega e si deforma. Per riattaccare il nastrino, la linguetta di plastica dovrà essere delicatamente reinserita nel suo alloggiamento.
    • Stacca delicatamente il nastrino del touchpad connesso alla scheda madre aiutandoti con un paio di pinzette a becco inclinato. Il nastrino del touchpad è connesso alla scheda madre mediante un connettore che si piega e si deforma. Per riattaccare il nastrino, la linguetta di plastica dovrà essere delicatamente reinserita nel suo alloggiamento.

    Be very careful when you detach the touchpad ribbon. You could disconnect the other end that is inside the touchpad. In fact I would recommend you use a plastic spudger to release the clips on the sides of the battery holder, and then lift the latch to the ZIF socket of the touchpad. If your touchpad is not working upon reassembly, then the other end of the ribbon cable my have came loose in the touchpad. Use a plastic opening tool to remove the back of the touchpad, and lift the brown latch of the ZIF socket and reinsert.

    Patrick - Réponse

    thanks for the advice

    TMC -

    currently doing this and have found the desoldering part the most difficult. i purchased a 40w solder on sale and attempted to remove with flux and wick to no avail. a buddy of mine tried with his station and no dice. at this point im thinking the contacts are lead? any advice?

    swammieslippyslappy -

    So the springs are annoying couldn't see were you talk about these as it's very fiddly to do the last step of putting it back together. Not just a reverse of taking it apart!

    Frank Theplank - Réponse

    I concur. The springs are the worst part of this job. It would be nice if someone edited this to add some tricks for reassembly.

    raysmalley -

    You just have to put the r2/l2 buttons on the top side. There's a space around that white rubber thing where you can just snap them in. So that you have all the shoulder buttons together before putting the 2 parts back together.

    Flow Von D -

    Tilt your controller and trigger so the triggers are pointing to the ground it stops the spring popping out so much place spring inside the trigger and clip on thats how i do it anyway :) the touchpad is my problem area replaced my stick covers and now it just doesnt work at all :(

    drwhatfunk -

    Thank you for this recommendation. Made disassembly SO much smoother.

    jeninholland02 - Réponse

    What I did for the Springs was place the spring on the button. Turned the button to where the spring is up on top then attached the button to the controller this helps keep the spring in place as you reattach it that is really the only trick that I found to it.

    Matthew Luna - Réponse

    “The touchpad ribbon is connected to the motherboard by a connector that flips to tighten and loosen” —> Just fixed a controller I bought in 2017. There was definitely no flip connector there, the ribbon simply went in. I guesss the internals changed. So beware: don’t mess with the female connector on the motherboard if there’s no obvious flip switch.

    jonl - Réponse

    Thank you. I just broke a piece of the plastic because it will not flip. I could not figure it out and was wondering if the version in these demonstrations was different than mine. Thank you for addressing this.

    nearthecross -

    never had spring problem

    DARKMATTER - Réponse

    Just want to say big thanks to ifixit for mentioning the flap. It worked like a charm. I searched high and low on all the usual forums, Reddit, Youtube, you name it. Who knew it was as simple as flipping the flap and no one even thought of mentioning it until I found this website.

    leehmclara - Réponse

  8. Sgancia la scheda madre dal resto della scocca frontale. I motori della vibrazione sono a stento agganciati al resto della scheda madre, perciò per facilitare la separazione, cerca di fornire un adeguato supporto alle loro estremità.
    • Sgancia la scheda madre dal resto della scocca frontale.

    • I motori della vibrazione sono a stento agganciati al resto della scheda madre, perciò per facilitare la separazione, cerca di fornire un adeguato supporto alle loro estremità.

    • Quando sarà il momento di estrarre la scheda madre, fai attenzione a non capovolgere troppo la scocca frontale, o tutti i tasti del controller potrebbero cadere.

    Yeah, the factory solder job for those motors on the mobo is terrible. Every time I open these up, I add more solder to those joints just to be safe.

    Robert - Réponse

  9. Se hai fatto tutto in maniera corretta, dovresti trovarti con queste tre parti, rispettivamente: Modulo della scheda madre Scocca anteriore
    • Se hai fatto tutto in maniera corretta, dovresti trovarti con queste tre parti, rispettivamente:

    • Modulo della scheda madre

    • Scocca anteriore

    • Scocca posteriore

    One day my R2 trigger refused to work all in a sudden. The second day it spread to my square button. I dissembled the controller to this step and found some liquid between the green motherboard and the black plastic holding it. I should not have bought a second-hand especially for a launch version. Anyways I cleaned it up and it still didn't work. I then went to ebay and bought a new motherboard. Basically it is a piece of delicate plastic like PCB. It is held in place by 3 plastic columns and 3 gaps for sliding underneath both triggers and the touch pad. Sorry for no pictures but a careful removal of the old one would give you the best illustration of how to put the new one back. First remove the rubber pads of the triggers, which allows you to slide in the PCB. Then there are another 2 small plastic columns at the back of the gap near the touch pad. There is no need to detach the rotors. A pair of tweezers would help greatly. My controller now works perfectly like new and thanks to the author.

    meaningless - Réponse

  10. Con le dita, rimuovi la copertura di gomma che protegge i bottoni. Aiutandoti con una pinzetta di metallo, rimuovi il bottone dal proprio alloggiamento. Aiutandoti con una pinzetta di metallo, rimuovi il bottone dal proprio alloggiamento.
    • Con le dita, rimuovi la copertura di gomma che protegge i bottoni.

    • Aiutandoti con una pinzetta di metallo, rimuovi il bottone dal proprio alloggiamento.

  11. Per rimuovere i tasti direzionali, adotta lostesso metodo che hai usato per i bottoni, rimuovendo la copertura di gomma a tirando fuori il tasto con una pinzetta di metallo. Per rimuovere i tasti direzionali, adotta lostesso metodo che hai usato per i bottoni, rimuovendo la copertura di gomma a tirando fuori il tasto con una pinzetta di metallo. Per rimuovere i tasti direzionali, adotta lostesso metodo che hai usato per i bottoni, rimuovendo la copertura di gomma a tirando fuori il tasto con una pinzetta di metallo.
    • Per rimuovere i tasti direzionali, adotta lostesso metodo che hai usato per i bottoni, rimuovendo la copertura di gomma a tirando fuori il tasto con una pinzetta di metallo.

  12. Per quanto riguarda i tasti Share ed Options, puoi usare un paio di pinzette dal becco inclinato per rimuoverli. Per quanto riguarda i tasti Share ed Options, puoi usare un paio di pinzette dal becco inclinato per rimuoverli.
    • Per quanto riguarda i tasti Share ed Options, puoi usare un paio di pinzette dal becco inclinato per rimuoverli.

  13. Affinché tu possa rimuovere il bottone PS dal controller, dovrai prima staccarne con le dita la copertura in gomma. Una volta fatto, usa le pinzette dal becco inclinato per rimuovere il bottone PS.
    • Affinché tu possa rimuovere il bottone PS dal controller, dovrai prima staccarne con le dita la copertura in gomma.

    • Una volta fatto, usa le pinzette dal becco inclinato per rimuovere il bottone PS.

    i have two ps4 controller and one of the r2 botton is mess up and it stuck and it is bent how can i fix that

    damarco harris - Réponse

    I have 2 PS4 controllers but the ps buttons are not working on both controllers. I tried checking the status of the controllers using my laptop, all the other buttons worked except for the ps button (13). I have dismantled the controllers to clean up dirts around the buttons but it still didn’t work. I need help to get the ps button working again. Thank you.

    Adeola Adegoke - Réponse

    Thank you ifixit.com

    Nait brahim - Réponse

Conclusion

Per riassemblare il tuo dispositivo, segui le istruzioni nell'ordine inverso.

105 autres ont terminé cette réparation.

Merci à ces traducteurs :

en it

100%

Johnny nous aide à réparer le monde ! Vous voulez contribuer ?
Commencez à traduire ›

Mark

Membre depuis le 21/01/2014

6 728 Réputation

4 tutoriels rédigés

Équipe

Cal Poly, Team 6-21, Maness Winter 2014 Membre de l'équipe Cal Poly, Team 6-21, Maness Winter 2014

CPSU-MANESS-W14S6G21

4 membres

47 tutoriels rédigés

21 commentaires

I pulled out my touch pad along with the motherboard when it was still attached how can I put this back in

Landen Nipper - Réponse

Pull out the ribbon the way the tutorial says and then you can place the touchpad back correctly. It needs to be put in from the inside of the controller, not the outside.

Luis Rodriguez -

where is how replace L2/R2? D=

ps4 - Réponse

This guide could be enhanced by showing the L1/L2, R1/R2 button cluster in some photos. I needed to replace the silicone grommet underneath the buttons due to Sony's design flaw of having R2/L2 press on the silicone with a blade shaped extension.

Joseph Bruni - Réponse

What to do If after cleaning some buttons no longer work? I was very careful when disassembling and reassembling the remote.

Amanda G Clark - Réponse

You might wanna make sure that flimsy plastic lining the buttons push is in its proper place. Sometimes it moves and if it doesn't line up just right it won't work.

Luis Rodriguez -

I took the "caveman" approach to this tutorial because I spilled soda near the controller and the circle button was sticky. It was an emergency operation done with a Phillips one size too large, a pocket knife for a spudger, and my cigar fingers for forceps. I must say, after some initial confusion, this tutorial helped me put it back together easily without breaking anything (a minor miracle all on its own). Thank for this.

Luis Rodriguez - Réponse

I need help. The up and right direction on the d-pad are not functioning. I took controller apart and made sure everything was clean and unfortunately did not fix problem. My question is has anyone else had this issue and if I buy a new silicon part for the d-pad will that fix it?

Borg914 - Réponse

My R2 button is constant being pressed. Even after I opened it and cleaned it. Please help me with this??

I connected it to pc and even removed the R2 button while checking for the buttons on pc,and button 8 (I.e R2 button on controller) shows as pressed all the time even when it's not there.

Obaid Haideri - Réponse

The “up" button on my d-pad has not been working recently so I followed the tutorial (helpful by the way), found no obvious problems, put it all back together, but the button still will not work. Any tips?

Fragasha - Réponse

Are the contacts lining up right? That might be the problem.

Luis Rodriguez -

how to clean the green circuit board because ps button is unresponsive? the true circuit button how to clean or repair it? cause mine is not responding in the motherboard assembly

ruzzyricor - Réponse

My vibration motor has fallen out and the wires are disconnected, how can I fix it?

Morris Vahla - Réponse

After I did this my right dpad button stopped functioning, is there a way to fix this?

maltamirano26 - Réponse

Where can I buy Grey Reset Button Extension

mcj0064 - Réponse

This is the original model. How about an update since there have been about 3 new assemblies and a new version of the DS4?

Eli Hanson - Réponse

Here is a solution to a broken R2 button. Really simple fix.

https://youtu.be/Lx3La8a169Q

Alex Manzano - Réponse

My PS4 is registering R2 button input without me pressing anything on the Dualshock 4. How can I fix it? This is only apparent when I play games… For example, when I play Spiderman where R2 is used for sprinting and web swinging, Spiderman will alternate between running and jogging, without me actually providing any kind of input via R2.

vinaymenon64 - Réponse

I have a triangle button sticking when i play a combat game it just happen the other day.

It seems stuck down in the controler it still work but it hard to press down when i need to use it.

What do you think the problem is?

jac02874 - Réponse

Thank you so much

Hussain Safaa - Réponse

After reassembling the controller won’t connect to the ps4. It will connect to the iPhone though.. what can I do?

ren smith - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 51

7 derniers jours : 262

30 derniers jours : 1,493

Total : 226,169