Aller au contenu principal

Introduction

Replacing the motor is not difficult. It should take about ten minutes.

Pièces

Aucune pièce spécifiée.

  1. Push the button on the back to release the lid. (Missing on this example device.)
    • Push the button on the back to release the lid. (Missing on this example device.)

    • In the photo on the device page it is red.

  2. Unscrew the dasher by holding it in the middle and turning clockwise. You will have to spin it quite a bit.
    • Unscrew the dasher by holding it in the middle and turning clockwise.

    • You will have to spin it quite a bit.

    • From here, you can now replace the dasher entirely.

    • Alternately, you can continue to step 3 to further disassemble the dasher components.

    • To reassemble the device, follow these instructions in reverse order.

  3. To take the dasher apart, remove the three 5.5 mm Phillips #00 screws embedded in the plastic.  **The 3rd screw is behind the hand in the picture Carefully pull the two pieces apart.
    • To take the dasher apart, remove the three 5.5 mm Phillips #00 screws embedded in the plastic. **The 3rd screw is behind the hand in the picture

    • Carefully pull the two pieces apart.

    • When you've finished taking apart the dasher, you should have two parts that are shown in the second picture in this step.

  4. Fix Kits pour iPhone X

    Finie la garantie ? Pas de soucis, nous avons de quoi réparer.

    Acheter maintenant

    Fix Kits pour iPhone X

    Finie la garantie ? Pas de soucis, nous avons de quoi réparer.

    Acheter maintenant
  5. After removing the dasher, turn the device so that you can see the “lock” and “unlock” symbols on the back.
    • After removing the dasher, turn the device so that you can see the “lock” and “unlock” symbols on the back.

    • Twist the casing so that it is in the unlocked position and remove it from the bottom half of the machine.

  6. Unscrew the five screws and remove the piece labeled in the picture. You should now be able to see the motor. Unscrew the five screws and remove the piece labeled in the picture. You should now be able to see the motor.
    • Unscrew the five screws and remove the piece labeled in the picture. You should now be able to see the motor.

  7. Lay the device on its side.
    • Lay the device on its side.

    • Remove the 4 gray rubber “feet” by pulling them straight outward.

    • Remove the four 5.5 mm Phillips #00 screws that are under them.

    • Remove the bottom plastic cover.

  8. Remove the two  5.5 mm Phillips #00 screws holding a bracket to keep the cord in place.
    • Remove the two 5.5 mm Phillips #00 screws holding a bracket to keep the cord in place.

    • Remove the the bracket so the chord has room to move.

  9. Remove the topmost 2  5.5 mm Phillips #00 screws that hold the motor in it’s casing. Remove and replace the motor. Remove and replace the motor.
    • Remove the topmost 2 5.5 mm Phillips #00 screws that hold the motor in it’s casing.

    • Remove and replace the motor.

Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Kirsty van Dam

Membre depuis le 24/03/2015

119 Réputation

1 tutoriel rédigé

Équipe

University of Alabama, Team 1-5, Naidoo Spring 2015 Membre de l'équipe University of Alabama, Team 1-5, Naidoo Spring 2015

UA-NAIDOO-S15S1G5

4 membres

2 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 3

Total : 699