Réparez vos affaires Communauté Boutique

SwagTron T1 Gyroscope Replacement

Introduction

This guide will show you how to replace the gyroscope component of your SwagTron T1. This may be necessary if the self-balancing function of your hoverboard is not working correctly. Before attempting this replacement, recalibrate your SwagTron. If the problem persists, continue with this replacement. This replacement can be done for the gyroscope component on either side of your SwagTron T1.

Ce dont vous avez besoin

  1. SwagTron T1 Gyroscope Replacement, Back Panels: étape 1, image 1 de 1

    • Ensure that the SwagTron is off.

    • Turn the SwagTron upside down to see the underside.

    Modifier

  2. SwagTron T1 Gyroscope Replacement: étape 2, image 1 de 3 SwagTron T1 Gyroscope Replacement: étape 2, image 2 de 3 SwagTron T1 Gyroscope Replacement: étape 2, image 3 de 3

    • Unscrew the eighteen 10mm screws that secure the back panels using a Phillips #2 screwdriver.

    • The screws are tightly in place. It will take effort to screw them out.

    • The panel is still attached to the SwagTron by wires that go to the motherboard.

    • Carefully lift the panels off

    Modifier

  4. SwagTron T1 Gyroscope Replacement: étape 3, image 1 de 3 SwagTron T1 Gyroscope Replacement: étape 3, image 2 de 3 SwagTron T1 Gyroscope Replacement: étape 3, image 3 de 3

    • Follow the wires from the panels to the motherboard.

    • You may need to cut any zip ties that are holding the wires together.

    • There is one connection on the battery side and three on the other side that must be removed.

    • These connections may be difficult to remove. Try to securely press the connection and pull firmly.

    • Your back panels are now completely removed.

    Modifier

  5. SwagTron T1 Gyroscope Replacement, Gyroscope: étape 4, image 1 de 2 SwagTron T1 Gyroscope Replacement, Gyroscope: étape 4, image 2 de 2

    • Disconnect the gyroscope by disconnecting the wires attached to it. These wires are black, green, blue and red.

    Modifier

  6. SwagTron T1 Gyroscope Replacement: étape 5, image 1 de 1

    • Using your Phillips #2 screwdriver, remove the four 8mm screws marked in red from the gyroscope.

    Modifier

  7. SwagTron T1 Gyroscope Replacement: étape 6, image 1 de 3 SwagTron T1 Gyroscope Replacement: étape 6, image 2 de 3 SwagTron T1 Gyroscope Replacement: étape 6, image 3 de 3

    • Carefully remove the gyroscope component from the SwagTron.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

9 autres ont terminé cette réparation.

Auteur

avec 3 autres contributeurs

Teagan Allen

Membre depuis le 04/18/17

426 Réputation

2 tutoriels rédigés

Badges: 10

+ 7 badges supplémentaires

Équipe

Cal Poly, Team S17-G5, Banghart Spring 2017 Membre de l'équipe Cal Poly, Team S17-G5, Banghart Spring 2017

CPSU-BANGHART-S17S17G5

4 membres

5 tutoriels rédigés

5 commentaires

I cannot find a Swagtron T1 replacement gyroscope anywhere on the internet. Any help would be extremely appreciated!! Thank you!

Gavin Hosler - Réponse

Amazon.com Keyword: CertiCable

Jesse Griffis -

Where do you get the replacement?

Brittany Conner - Réponse

Can’t find gyroscope for a t5 hover board please help.

jbswearingen70739 - Réponse

I just got mine today and after the first hour I ran into a shoe and then I tried recalibrating it but it was no use. If someone knows what’s going on please tell me! Thank you :)

Elia Leon - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 2

7 derniers jours : 9

30 derniers jours : 39

Total : 7,217