Aller au contenu principal

Swagtron T3 Gyroscope Replacement

Ce dont vous avez besoin

  1. Swagtron T3 Gyroscope Replacement, Cover: étape 1, image 1 de 2 Swagtron T3 Gyroscope Replacement, Cover: étape 1, image 2 de 2
    • Make sure the hoverboard is completely powered off and unplugged from any outlets.

    • Flip the Swagtron so that the footpads are facing the ground.

    • Unscrew the sixteen 9.4 mm Phillips #1 machine screws on the side of the Swagtron that is now facing upwards.

  2. Swagtron T3 Gyroscope Replacement: étape 2, image 1 de 3 Swagtron T3 Gyroscope Replacement: étape 2, image 2 de 3 Swagtron T3 Gyroscope Replacement: étape 2, image 3 de 3
    • Be careful with the small blue capacitors indicated by the orange box. There are many of these capacitors in the device.

    • Slowly lift the backside cover.

    • Both sides lift up the same way, but the motherboard is under one side and the battery is under the other.

    • Detach the four cables connected to the cover by pinching the connector clips and pulling the cables out:

    • Three cables on the motherboard side.

    • Two red cables with white connectors and one white cable with a white connector.

    • One yellow cable with a black connector on the battery side.

    • After detachment, you should be able to completely remove the backside cover.

  3. Swagtron T3 Gyroscope Replacement, Gyroscope: étape 3, image 1 de 1
    • The gyroscope is a blue rectangular circuit board on top of a white base and is closest to the wheel.

    • Detach the four cables connecting the gyroscope to the hoverboard by pinching the connector clips and pulling the cables out:

    • Three red and black cables with white connectors.

    • One multicolored cable with a black connector.

  4. Swagtron T3 Gyroscope Replacement: étape 4, image 1 de 1
    • Uncrew the four 7.2 mm Phillips #1 self-drilling screws connecting the blue gyroscope to the white plastic holding piece.

  5. Swagtron T3 Gyroscope Replacement: étape 5, image 1 de 2 Swagtron T3 Gyroscope Replacement: étape 5, image 2 de 2
    • Cut the plastic cable tie holding the cables together with utility scissors.

    • Disconnect the blue/green cable from the blue/white cable by pinching the connector clips and pulling the cables apart.

  6. Swagtron T3 Gyroscope Replacement: étape 6, image 1 de 1
    • Gently lift the blue gyroscope off of the white plastic holder piece.

    • After reassembling the Swagtron with the new gyroscope, check to make sure your Swagtron is balancing properly.

    • If it is still unbalanced, repeat all steps in this guide with the gyroscope by the other wheel.

Conclusion

To reassemble your device, follow these instructions in reverse order.

3 autres ont terminé cette réparation.

Emily Richter

Membre depuis le 04/10/17

351 Réputation

1 tutoriel rédigé

Équipe

Cal Poly, Team S13-G3, Forte Spring 2017 Membre de l'équipe Cal Poly, Team S13-G3, Forte Spring 2017

CPSU-FORTE-S17S13G3

4 membres

4 tutoriels rédigés

3 commentaires

Where can one buy the new gyroscope?

Mike - Réponse

Where is the best place to buy the gyroscope for the T3?

I see Ebay sells complete kits with motherboards and all.

Are they compatible?

Mike - Réponse

where can I buy new gyroscope

roccovalletta - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 1

7 derniers jours : 8

30 derniers jours : 37

Total : 4,871