Aller au contenu principal
  1. Cette étape n’est pas traduite. Aidez à la traduire

    Remove the four Torx T5 screws from the back panel.
    • Remove the four Torx T5 screws from the back panel.

  2. Cette étape n’est pas traduite. Aidez à la traduire

    Wedge a spudger in between the front and back panel.
    • Wedge a spudger in between the front and back panel.

    • Apply leverage downwards to the spudger in order to remove the back panel.

  3. Cette étape n’est pas traduite. Aidez à la traduire

    Slide the battery out from under the brown wire-tape.
    • Slide the battery out from under the brown wire-tape.

    • Be careful of the wires still connected to the other end of the battery. Do not pull or damage may occur.

  4. Cette étape n’est pas traduite. Aidez à la traduire

    Slowly pull the white plug from its receptor. Grasp its sides firmly with a pair of tweezers and gently wiggle from side to side.
    • Slowly pull the white plug from its receptor. Grasp its sides firmly with a pair of tweezers and gently wiggle from side to side.

  5. Cette étape n’est pas traduite. Aidez à la traduire

    Unscrew the 2 Philips #00 screws on each end of the motherboard.
    • Unscrew the 2 Philips #00 screws on each end of the motherboard.

  6. Cette étape n’est pas traduite. Aidez à la traduire

    Pull off the black memory card slot piece with tweezers.
    • Pull off the black memory card slot piece with tweezers.

  7. Cette étape n’est pas traduite. Aidez à la traduire

    Unscrew the 2 Philips #00 screws on each side of the charging port.
    • Unscrew the 2 Philips #00 screws on each side of the charging port.

  8. Cette étape n’est pas traduite. Aidez à la traduire

    Disconnect 2 brown wire-tape ends from each end of the motherboard. Gently pull straight out with tweezers. Disconnect 2 brown wire-tape ends from each end of the motherboard. Gently pull straight out with tweezers.
    • Disconnect 2 brown wire-tape ends from each end of the motherboard. Gently pull straight out with tweezers.

  9. Cette étape n’est pas traduite. Aidez à la traduire

    Pull the motherboard and screen component diagonally up and left away from the auxiliary port entrance to remove.
    • Pull the motherboard and screen component diagonally up and left away from the auxiliary port entrance to remove.

    • Glue connecting the auxiliary port to the casing may make it difficult to remove. Gently apply force as needed.

  10. Cette étape n’est pas traduite. Aidez à la traduire

    Disconnect the 2 brown wire-tape ends from the left side of the battery slot on the motherboard using tweezers.
    • Disconnect the 2 brown wire-tape ends from the left side of the battery slot on the motherboard using tweezers.

  11. Cette étape n’est pas traduite. Aidez à la traduire

    Disconnect the large brown wire-tape from the motherboard. Peel the black tape back from the wire-tape using tweezers. Lift the black, hinged, plastic lock with tweezers to release the wire-tape.
    • Disconnect the large brown wire-tape from the motherboard.

    • Peel the black tape back from the wire-tape using tweezers.

    • Lift the black, hinged, plastic lock with tweezers to release the wire-tape.

    • The screen and motherboard components can now be separated from each other.

  12. Cette étape n’est pas traduite. Aidez à la traduire

    Unscrew the 2 Philips #00 screws from the bottom edge of the screen component.
    • Unscrew the 2 Philips #00 screws from the bottom edge of the screen component.

  13. Cette étape n’est pas traduite. Aidez à la traduire

    Take off the brown wire-tape from the small circuit board component.
    • Take off the brown wire-tape from the small circuit board component.

    • Lift up so that the black plastic hinge piece swings open and the tape can be removed.

  14. Cette étape n’est pas traduite. Aidez à la traduire

    Warning: If you are too rough with the screwdriver, you can permanently damage the display. Use a Slot SL1.5 screwdriver to pry the touchscreen shell from the display component using the 4 slots around the entire component Use a Slot SL1.5 screwdriver to pry the touchscreen shell from the display component using the 4 slots around the entire component
    • Warning: If you are too rough with the screwdriver, you can permanently damage the display.

    • Use a Slot SL1.5 screwdriver to pry the touchscreen shell from the display component using the 4 slots around the entire component

Ligne d'arrivée

Daniel Wiseman

Membre depuis le 20/01/2012

133 Réputation

6 tutoriels rédigés

Équipe

Cal Poly, Team 10-33, Amido Winter 2012 Membre de l'équipe Cal Poly, Team 10-33, Amido Winter 2012

CPSU-AMIDO-W12S10G33

4 membres

8 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 1

7 derniers jours : 3

30 derniers jours : 14

Total : 737