Réparez vos affaires Communauté Boutique

TomTom One XL Charging Port Replacement

Introduction

This guide will show you how to replace or reconnect the charging port to the motherboard.

Ce dont vous avez besoin

  1. TomTom One XL Charging Port Replacement, Back Panel: étape 1, image 1 de 2 TomTom One XL Charging Port Replacement, Back Panel: étape 1, image 2 de 2

    • Remove the 4 .4mm screws on the back of the device.

    Modifier

  2. TomTom One XL Charging Port Replacement: étape 2, image 1 de 1

    • Using the palate knife tool, pry the back from the LCD screen. Apply a moderate pressure to separate them.

    • You can rotate TOMTOM XL to make prying back off easier.

    • Be careful not to injure the two wires connecting the pieces.

    Modifier

  3. TomTom One XL Charging Port Replacement: étape 3, image 1 de 1

    • After prying both halves apart, they will be connected by two wires.

    • Carefully set the two halves next to each other making sure not to stress or damage the wires.

    Modifier

  5. TomTom One XL Charging Port Replacement: étape 4, image 1 de 2 TomTom One XL Charging Port Replacement: étape 4, image 2 de 2

    • Using the tweezers separate the wires connecting the battery and speaker to the mother board.

    • Be gentle while pulling the wires out, the plugs are easily injured.

    Modifier

  6. TomTom One XL Charging Port Replacement, Charging Port: étape 5, image 1 de 2 TomTom One XL Charging Port Replacement, Charging Port: étape 5, image 2 de 2

    • If this is your first time solder then refer to IFixIt's safety guide.

    • Locate where the charger port goes on the circuit board.

    • Locate the four connecter on circuit board and charger port which need to be soldered.

    • Don't forget, the soldering iron is hot.

    Modifier

  7. TomTom One XL Charging Port Replacement: étape 6, image 1 de 3 TomTom One XL Charging Port Replacement: étape 6, image 2 de 3 TomTom One XL Charging Port Replacement: étape 6, image 3 de 3

    • Using your plastic opening tool press down firmly on the top of the charger port.

    • While the soldering iron is hot press it again the four corners of the charger port.

    • Don't touch the charger port with your hands, it may have heated up during soldering.

    Modifier

  8. TomTom One XL Charging Port Replacement: étape 7, image 1 de 3 TomTom One XL Charging Port Replacement: étape 7, image 2 de 3 TomTom One XL Charging Port Replacement: étape 7, image 3 de 3

    • Let the circuit board and charger port cool down for a few minutes.

    • Lift circuit board up, after making sure its cool, to see if four corners are all connected.

    • Plug in the charger to make sure it works, if not repeat steps and make sure the port is making a clean connection.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Auteur

avec 2 autres contributeurs

DeVhan

Membre depuis le 03/11/15

401 Réputation

4 tutoriels rédigés

Badges: 4

+ 1 badge de plus

Équipe

Colorado Springs, Team 9-6, Panko Spring 2015 Membre de l'équipe Colorado Springs, Team 9-6, Panko Spring 2015

UCCS-PANKO-S15S9G6

3 membres

5 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 3

30 derniers jours : 8

Total : 2,410