Introduction

Remove the front cover in order to access the internal components of the laptop.

Pièces

Aucune pièce nécessaire.

Locate the two sliding locks indicated in the photo.
  • Locate the two sliding locks indicated in the photo.

  • Slide the right lock (labeled "1") to the right. It will remain in the unlocked position.

  • Slide the left lock (labeled "2") to the left and hold it in place.

Ajouter un commentaire

While holding the left lock, place your finger in the indentation next to the battery and lift the battery out.
  • While holding the left lock, place your finger in the indentation next to the battery and lift the battery out.

Ajouter un commentaire

  • Remove the four screws indicated in the photos using a Phillips 00 Screwdriver. Left to right: 6mm button-head, 3mm flat-head, 6mm button-head, 6mm button-head.

Ajouter un commentaire

  • With your hands, grasp the speaker cover on the edge nearest to the screen.

  • Pry the speaker cover upward.

Ajouter un commentaire

  • Remove the speaker cover. Your laptop will look like this photo when the speaker cover has been removed.

Ajouter un commentaire

  • Remove the two 4mm flat-head screws indicated in the photo.

Ajouter un commentaire

  • Slightly lift and ease the keyboard forward, toward the screen, until the tabs clear the case.

  • When all the tabs are free, slowly lift the bottom of the keyboard while keeping the top of the keyboard angled down. Continue to carefully rotate the keyboard over until you can access the ribbon cable that is still connecting it to the computer.

Ajouter un commentaire

  • The Ribbon Cable must be disconnected here to release the keyboard.

  • Using a plastic splunger or the tip of your screwdriver gently push upward on the two black tabs securing the connection.

  • When the black plastic bar running across the cable is unseated you can slowly and carefully pull the ribbon cable free.

  • You can now lift and remove the keyboard.

Ajouter un commentaire

  • Locate the gray wire on the right.

  • Detach the white end by gently pulling each socket away from the other.

Ajouter un commentaire

  • On the left, locate the black and white wires with gold tips on the end.

  • Pull up on the wires to detach them.

Ajouter un commentaire

  • Locate the thick tan cord on the left.

  • Slide the tan cord as shown to detach it.

Ajouter un commentaire

  • On the right, locate the thick black wire with the white rectangular end.

  • Pull up on it to detach it.

Ajouter un commentaire

  • Remove the four 8mm button-head screws that are located in the top right (2) and top left corners (2) of the front cover. Use a Phillips 00 Screwdriver.

Ajouter un commentaire

  • Once all the wires are detached and screws are removed, pull up on the monitor to remove it.

There were two additional screws on the back of the laptop I had to remove to get the screen off.

Dylan Carter - Réponse

  • Locate the screws that are shown in the image.

  • Remove the fourteen 6mm button-head screws with a Phillips 00 Screwdriver.

Ajouter un commentaire

  • Lift up on the front cover to remove it.

There was an additional screw in the front cover to the right of the wireless card that I had to remove; it was already gone in earlier pictures in the walkthrough

Dylan Carter - Réponse

Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Cameron Howard

Membre depuis le 16/04/2013

62 Réputation

3 tutoriels rédigés

Équipe

Cal Poly, Team 17-6, Regan Spring 2013 Membre de l'équipe Cal Poly, Team 17-6, Regan Spring 2013

CPSU-REGAN-S13S17G6

5 membres

11 tutoriels rédigés

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 5

Total : 1,018