Menu 

Vos paramètres

Toshiba Satellite A85-S107 15" Hard Drive Replacement

Rédigé par : Travis (et 10 autres contributeurs)
  • Commentaires : 0
  • Favoris : 0

Difficulté

Facile

Étapes

7

Temps nécessaire

2 - 5 minutes

Sections

2

Drapeaux

3

Needs Better Images

A besoin de meilleures images

De meilleures photos amélioreront ce tutoriel. Aider en proposant de nouvelles photos!

Missing Prerequisites

Conditions préalables manquantes

Ce tutoriel ne donne pas d'informations sur le début de la procédure. Créez un tutoriel de conditions préalables !

Missed a Step

Une étape a été sautée

Oups ! Il manque encore des étapes importantes à ce tutoriel.

Introduction

Use this guide to replace or install the hard drive in your Toshiba laptop.

  1. Power off the laptop.

    • Power off the laptop.

    • Disconnect the power cable from the laptop. If you do not, electric shock may result.

    Modifier

  2. Flip the laptop over and orient it such that the battery faces towards you and the front faces away from you as shown in the diagram.

    • Flip the laptop over and orient it such that the battery faces towards you and the front faces away from you as shown in the diagram.

    • Unlock the battery by sliding the tab shown to the right

    • This tab will latch into place.

    Modifier

  3. Slide the tab shown to the left and remain holding it. This tab does not lock into place like in the first step.

    • Slide the tab shown to the left and remain holding it.

    • This tab does not lock into place like in the first step.

    • Place your thumb on the grips of the battery as shown.

    • While holding onto the grips, pull the battery towards you and away from the laptop.

    Modifier

  5. Flip the computer around so the battery is facing away from you.

    • Flip the computer around so the battery is facing away from you.

    Modifier

  6. Locate 5mm Philips #0 screw on hard drive cover. Remove these two 5mm Phillips #0 screws using the Phillips #0 Screwdriver.

    • Locate 5mm Philips #0 screw on hard drive cover.

    • Remove these two 5mm Phillips #0 screws using the Phillips #0 Screwdriver.

    Modifier

  7. Insert the plastic opening tool into the tab shown and lift up to remove the lower left plate. If the hard drive panel is difficult to remove and feels like it is going to break, DO NOT force it. Check to confirm that all the screws are removed before attempting again.

    • Insert the plastic opening tool into the tab shown and lift up to remove the lower left plate.

    • If the hard drive panel is difficult to remove and feels like it is going to break, DO NOT force it. Check to confirm that all the screws are removed before attempting again.

    Modifier

  8. Use plastic opening tool to lift hard drive out of case.

    • Use plastic opening tool to lift hard drive out of case.

    • Lift the left side of the hard drive and slide it out towards the left.

    • We do not have all the required parts for this guide.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Auteur

avec 10 autres contributeurs

Travis

Membre depuis le 13/04/2013

13 Réputation

5 tutoriels rédigés

Badges: 9

+ 6 badges supplémentaires

Équipe

Cal Poly, Team 10-38, Amido Spring 2013 Membre de l'équipe Cal Poly, Team 10-38, Amido Spring 2013

CPSU-AMIDO-S13S10G38

4 membres

8 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 6

Total : 728