Aller au contenu principal

Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.

Ce dont vous avez besoin

  1. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 1, image 1 de 2 : étape 1, image 2 de 2
    • Before repairing your laptop, power down the system, disconnect the charger if necessary and remove the battery.

    • Use the flat edge of the plastic opening tool to pry open the narrow plastic strip above the keyboard.

  2. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 2, image 1 de 1
    • Remove the three 3mm screws with a Phillips#00 Screwdriver.

  3. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 3, image 1 de 1
    • Lift the keyboard away from the top side of the laptop.

    • Do not pull the keyboard away too hard. It is still connected by the fragile ribbon cable (shown in the red square).

  4. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 4, image 1 de 2 : étape 4, image 2 de 2
    • Disconnect the keyboard cable that is still attached to the keyboard.

    • Unlatch the fastener.

    • Using your hands, pull the keyboard connector out, not up.

  5. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 5, image 1 de 2 : étape 5, image 2 de 2
    • Flip the laptop over to access the battery.

    • Remove the battery by sliding fingers away from each other and lifting up the tab at the same time.

  6. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 6, image 1 de 1
    • Remove the twelve 10mm screws with a Phillips #00 screwdriver.

    • Remove the cover over the hard drive (upper right in photo) and remove the four 10mm screws at the four corners.

  7. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 7, image 1 de 1
    • Remove the three 4mm screws with a Phillips #00 screwdriver.

  8. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 8, image 1 de 1
    • Flip the laptop over so it's in the right-side-up position.

    • Lift the grey plastic casing up and unhook any wires attached to the casing.

    • Remove the five 10mm screws, each with a label 'F10' next to them.

  9. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 9, image 1 de 2 : étape 9, image 2 de 2
    • Disconnect the flat thin wire connecting the track pad to the motherboard by pulling it straight out.

    • Disconnect the thin red wire on the right side of the motherboard.

  10. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 10, image 1 de 1
    • Remove the two 6mm screws with a Phillips #00 screwdriver.

  11. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 11, image 1 de 2 : étape 11, image 2 de 2
    • Disconnect the red and yellow wires connecting the fan to the motherboard by pulling the wires straight out.

    • Remove the fan.

  12. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 12, image 1 de 1
    • Remove the following with a Phillips #00 Screwdriver:

    • Six 7mm Phillips Head screws

    • One 5 mm Phillips Head screw

    • Remove the LCD screen tab

  13. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 13, image 1 de 2 : étape 13, image 2 de 2
    • A red wire connects the motherboard to the computer, so release the wire by pulling it straight out.

    • After all the screws are removed, lift the motherboard up and away from the earphone jacks that are located at the front of the laptop.

Ligne d'arrivée

Une autre personne a terminé cette réparation.

Mike Kennedy

Membre depuis le 04/18/13

160 Réputation

4 tutoriels rédigés

Équipe

Cal Poly, Team 2-21, Maness Spring 2013 Membre de l'équipe Cal Poly, Team 2-21, Maness Spring 2013

CPSU-MANESS-S13S2G21

4 membres

5 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 6

30 derniers jours : 14

Total : 3,052