Aller au contenu principal

Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.

Ce dont vous avez besoin

  1. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 1, image 1 de 3 : étape 1, image 2 de 3 : étape 1, image 3 de 3
    • Locate the battery locks on the bottom of the laptop.

    • Slide the right lock outwards, until it locks into place.

    • Slide and hold the left lock outwards and hold it in place.

  2. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 2, image 1 de 1
    • While holding the lock in place, slide the battery out towards you.

  3. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 3, image 1 de 1
    • Using a #1 Phillips screwdriver, remove the 5.8 mm screw in the battery slot.

  4. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 4, image 1 de 1
    • Use a plastic opening tool to pry off the plastic panel above the keyboard.

  5. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 5, image 1 de 2 : étape 5, image 2 de 2
    • Unscrew the four 3.7 mm screws at the top of the keyboard using a #1 Phillips screwdriver.

  6. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 6, image 1 de 1
    • Slowly lift the keyboard out, up and towards the screen.

    • Do not try to remove the keyboard completely because it is still attached to the motherboard.

  7. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 7, image 1 de 1
    • Using a plastic opening tool, flip the ZIF connector up to release the ribbon and the keyboard.

  8. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 8, image 1 de 2 : étape 8, image 2 de 2
    • Unscrew the three 4.6 mm screws holding the panel using a #1 size Phillips head screwdriver. The panel is centered on the bottom of the laptop.

  9. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 9, image 1 de 1
    • Remove the cover, firmly lifting from the indent. It is recommended that you leave the screws in the panel.

  10. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 10, image 1 de 3 : étape 10, image 2 de 3 : étape 10, image 3 de 3
    • Push the two tabs outwards, away from the RAM. The RAM should spring up.

  11. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 11, image 1 de 3 : étape 11, image 2 de 3 : étape 11, image 3 de 3
    • Pull the top RAM stick out gently.

    • Repeat steps 3 and 4 for the bottom RAM stick.

    • When installing the new RAM, line up the notches in the RAM's contacts and insert it at the same angle you removed it.

  12. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 12, image 1 de 1
    • Remove the single screw securing the optical drive, and pull the optical drive out.

  13. Cette étape n’est pas traduite. Aidez à la traduire

    : étape 13, image 1 de 3 : étape 13, image 2 de 3 : étape 13, image 3 de 3
    • Remove the eight M2.5x6.5 screws securing the palmrest to the base.

    • Remove all connectors from their sockets, except for the LCD cable. That one doesn't need to be removed.

    • Flip the laptop over and remove the twelve M2.5x6.5 screws.

    • Also be sure to remove the four short, big-headed Philips screws from under where the battery was.

    • Remove the two final screws securing the palmrest to the base, which are where the optical drive's faceplate was.

    • Now use a spudger to separate the palmrest and the base.

  14. Cette étape n’est pas traduite. Aidez à la traduire

    • Now, you can simply flip the laptop standing on its left side, pull the connector out from where the memory cover was, and then yank the jack from the adhesive holding it.

Ligne d'arrivée

Une autre personne a terminé cette réparation.

Joseph Sctbunio

Membre depuis le 09/23/17

7 332 Réputation

42 tutoriels rédigés

2 commentaires

Terrible, terrible and terrible again. You show nothing at the end about getting the jack out. I will now know not to look at any of your repairs. Totally useless.

Dave Wiloch - Réponse

I apologize for my waste of your time. However, if my guide was as terrible as you say, you could have contributed to the guide instead of leaving such a comment. It would have helped more people.

Regardless, I do agree with your point, and I do not know why I had stopped the guide this early. I usually go in-depth, and have even corrected others’ guides.

I will do better next time.

Joseph Sctbunio -

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 1

7 derniers jours : 9

30 derniers jours : 35

Total : 685