Aller au contenu principal

Réparez vos affaires

Droit à la réparation

Pièces & Outils

Introduction

How to replace the TRITTON Kunai's left speaker.

Pièces

Aucune pièce spécifiée.

  1. Firmly grasp the black ear cushion with one hand and the white speaker frame with the other hand. Forcibly pull the ear cushion and speaker frame in opposite directions, until the right ear cushion separates from the right ear frame.
    • Firmly grasp the black ear cushion with one hand and the white speaker frame with the other hand.

    • Forcibly pull the ear cushion and speaker frame in opposite directions, until the right ear cushion separates from the right ear frame.

  2. Remove the two 9 mm screws indicated in red with a PH00 screwdriver. Remove the two 7 mm screws indicated in orange with a PH00 screwdriver.
    • Remove the two 9 mm screws indicated in red with a PH00 screwdriver.

    • Remove the two 7 mm screws indicated in orange with a PH00 screwdriver.

    • Separate the black horseshoe shaped frame from the right speaker frame.

  3. Remove the two 7 mm screws indicated in red using a PH00 screwdriver. Separate the black bracket and then the rail adjustment from the right speaker frame.
    • Remove the two 7 mm screws indicated in red using a PH00 screwdriver.

    • Separate the black bracket and then the rail adjustment from the right speaker frame.

  4. Remove the six 7 mm screws indicated in red using a PH00 screwdriver. Separate the black speaker console from the right speaker frame.
    • Remove the six 7 mm screws indicated in red using a PH00 screwdriver.

    • Separate the black speaker console from the right speaker frame.

  5. Kits pour Nintendo Switch

    Une solution rapide pour reprendre le jeu

    Acheter un kit pour Switch

    Kits pour Nintendo Switch

    Une solution rapide pour reprendre le jeu

    Acheter un kit pour Switch
  6. Disconnect the red and white wires from the 16 Ohm speaker.
    • Disconnect the red and white wires from the 16 Ohm speaker.

  7. Squeeze the tip of the tweezers into the gap between the speaker and the speaker case.
    • Squeeze the tip of the tweezers into the gap between the speaker and the speaker case.

    • Remove the glue holding the speaker in place by scraping the glue with the tip of the tweezers.

  8. Remove the speaker from its circular shaped slot. Remove the speaker from its circular shaped slot.
    • Remove the speaker from its circular shaped slot.

    • Apply glue to the sides of your new 16 Ohm speaker.

  9. Insert your new speaker into the circular shaped slot located on the speaker cover. Insert your new speaker into the circular shaped slot located on the speaker cover.
    • Insert your new speaker into the circular shaped slot located on the speaker cover.

  10. Solder the wires you disconnected from the old speaker to the new speaker. The red wire is to be soldered to the far left terminal, while the white wire is to be soldered to the far right terminal.
    • Solder the wires you disconnected from the old speaker to the new speaker. The red wire is to be soldered to the far left terminal, while the white wire is to be soldered to the far right terminal.

    • Here is iFixit's soldering guide.

    • Solder with caution and try not to burn yourself.

Conclusion

To reassemble your device, follow steps 1 through 4 in reverse order.

3 autre(s) ont terminé cette réparation.

Elias El Tom

Membre depuis le 12/03/2015

338 Réputation

2 tutoriels rédigés

Équipe

UMass Dartmouth, Team 3-3, Duarte Spring 2015 Membre de l'équipe UMass Dartmouth, Team 3-3, Duarte Spring 2015

UMASSD-DUARTE-S15S3G3

4 membres

5 tutoriels rédigés

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 6

Total : 1,240