Réparez vos affaires Communauté Boutique

Visioneer OneTouch 7400 USB Belt Replacement

Introduction

Use this guide to remove the belt that moves the Visioneer OneTouch 7400 USB sensor bar for repair or replacement.

Ce dont vous avez besoin

  1. Visioneer OneTouch 7400 USB Belt Replacement, Outer Case: étape 1, image 1 de 1

    • On the bottom of the scanner, remove the screw at the top left side.

    Modifier

  2. Visioneer OneTouch 7400 USB Belt Replacement: étape 2, image 1 de 2 Visioneer OneTouch 7400 USB Belt Replacement: étape 2, image 2 de 2

    • Remove the rubber foot pad opposite the screw hole to expose a second screw hole.

    • Remove the screw beneath the foot-pad.

    Modifier

  3. Visioneer OneTouch 7400 USB Belt Replacement: étape 3, image 1 de 3 Visioneer OneTouch 7400 USB Belt Replacement: étape 3, image 2 de 3 Visioneer OneTouch 7400 USB Belt Replacement: étape 3, image 3 de 3

    • Rotate the scanner so the screw hole is located on the top left hand side.

    • Place the plastic opening tool between the top casement and bottom casement of scanner with the hook facing up.

    • Gently pry the two casements apart beginning above the screw hole and working your way around.

    • Note that the top and bottom casings are held together by a series of 6 tabs. There is one tab on each of the long sides of the scanner approximately 6 inches in from the corners. There are two tabs on each of the short sides of the scanner approximately 2.3 inches in from the corners. Use the spudger to unhook the tab from the top casement.

    Modifier

  4. Visioneer OneTouch 7400 USB Belt Replacement: étape 4, image 1 de 1

    • Separate the two casement pieces.

    Modifier

  6. Visioneer OneTouch 7400 USB Belt Replacement, Belt: étape 5, image 1 de 1

    • Remove the screw holding the tension spring in place.

    Modifier

  7. Visioneer OneTouch 7400 USB Belt Replacement: étape 6, image 1 de 1

    • Use the plastic opening tool to lift up the tension spring.

    • Be careful. The spring will fly.

    Modifier

  8. Visioneer OneTouch 7400 USB Belt Replacement: étape 7, image 1 de 1

    • Remove the belt from the spool.

    • The spool is a loose piece; don't lose it.

    Modifier

  9. Visioneer OneTouch 7400 USB Belt Replacement: étape 8, image 1 de 1

    • Loosen the belt enough to turn over the sensor bar.

    Modifier

  10. Visioneer OneTouch 7400 USB Belt Replacement: étape 9, image 1 de 2 Visioneer OneTouch 7400 USB Belt Replacement: étape 9, image 2 de 2

    • With the sensor bar turned upside down, remove the screw in the middle of the bar.

    • Lift off the metal plate if it does not come away with the screw.

    Modifier

  11. Visioneer OneTouch 7400 USB Belt Replacement: étape 10, image 1 de 1

    • Carefully lift the belt out of the groove in the sensor bar to remove.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Auteur

avec 4 autres contributeurs

Jena

Membre depuis le 10/18/13

608 Réputation

6 tutoriels rédigés

Badges: 9

+ 6 badges supplémentaires

Équipe

University of Maine, Team 1-13, Diaz Fall 2013 Membre de l'équipe University of Maine, Team 1-13, Diaz Fall 2013

UMAINE-DIAZ-F13S1G13

3 membres

14 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 0

Total : 276