Introduction

Use this guide to replace the bottom panel of your controller that you cracked by throwing it at the TV.

  1. Depress the battery release button on the top of the controller. Remove the battery holder from the controller.
    • Depress the battery release button on the top of the controller.

    • Remove the battery holder from the controller.

    • The standard option for Xbox 360 Wireless Controllers Battery Packs is AA batteries. A rechargeable battery is also available, but both battery options are removed from the controller in the same way.

  2. Use a pair of tweezers to peel the barcode sticker from the battery compartment.
    • Use a pair of tweezers to peel the barcode sticker from the battery compartment.

  3. Remove the seven 9.3 mm  T8 Security Torx screws securing the rear case to the front case.
    • Remove the seven 9.3 mm T8 Security Torx screws securing the rear case to the front case.

    • Insert a Spudger between the front and rear cases along the left edge of the controller.

    • Rotate the spudger toward the front of the controller, prying the two cases apart.

  4. Insert a spudger between the front and rear cases, near the headphone jack. Rotate the spudger toward the front of the controller to pry the two cases apart.
    • Insert a spudger between the front and rear cases, near the headphone jack.

    • Rotate the spudger toward the front of the controller to pry the two cases apart.

  5. Grasp the controller by the battery compartment and the headphone jack. Lift the battery compartment away from the headphone jack, separating the rear case from the front case and logic board.
    • Grasp the controller by the battery compartment and the headphone jack.

    • Lift the battery compartment away from the headphone jack, separating the rear case from the front case and logic board.

    • The battery contact springs are held in place by slots in the battery housing in the rear case. Be sure to realign them properly during reassembly.

  6. %Livraison gratuite pour toute commande supérieure à 100 $US ou contenant un Pro Tech Toolkit !

    Parcourez notre boutique
  7. Use the flat end of a spudger to remove the vibration motor cable, moving it upward from its socket on the logic board. Lift the vibration motor out of the front case.
    • Use the flat end of a spudger to remove the vibration motor cable, moving it upward from its socket on the logic board.

    • Lift the vibration motor out of the front case.

  8. Remove the vibration motor from the other side of the controller using the same method previously described. The right motor has significantly more counterweight than the left motor.
    • Remove the vibration motor from the other side of the controller using the same method previously described.

    • The right motor has significantly more counterweight than the left motor.

  9. Lifting from the headphone jack and power plug, remove the logic board from the front case. Lifting from the headphone jack and power plug, remove the logic board from the front case.
    • Lifting from the headphone jack and power plug, remove the logic board from the front case.

  10. Lift the bumper panel off of the front case. Lift the bumper panel off of the front case.
    • Lift the bumper panel off of the front case.

  11. Remove the rubber pad from the back of the D-pad.
    • Remove the rubber pad from the back of the D-pad.

  12. Remove the two 7.0 mm silver Phillips screws from the back of the D-pad.
    • Remove the two 7.0 mm silver Phillips screws from the back of the D-pad.

  13. The D-pad is secured to its backing by two diagonal clips, shown in red. Use a pair of tweezers and squeeze the clips together to release the D-pad from its backing.
    • The D-pad is secured to its backing by two diagonal clips, shown in red.

    • Use a pair of tweezers and squeeze the clips together to release the D-pad from its backing.

  14. Lift the D-pad backing out of its compartment on the front case. The D-pad remains below the front case.
    • Lift the D-pad backing out of its compartment on the front case.

    • The D-pad remains below the front case.

    • The D-pad will fall once its backing is removed. Be sure to support it as you remove the backing.

    • The backing is slotted to its compartment to ensure that it will always be aligned properly.

  15. Remove the rubber pad from the back of the input buttons.
    • Remove the rubber pad from the back of the input buttons.

  16. Using a pair or tweezers, remove the following buttons from the front panel: A Button
    • Using a pair or tweezers, remove the following buttons from the front panel:

    • A Button

    • B Button

    • X Button

    • Y Button

    • Start Button

    • Select Button

    • Guide Button

  17. Using a pair of tweezers, remove the LED ring from the front panel.
    • Using a pair of tweezers, remove the LED ring from the front panel.

  18. Insert a spudger between the lower panel and front case. Slide the spudger along the gap between the two case components. Lift the lower panel off of the front case.
    • Insert a spudger between the lower panel and front case.

    • Slide the spudger along the gap between the two case components.

    • Lift the lower panel off of the front case.

Conclusion

To reassemble your device, follow these instructions in reverse order.

13 autre(s) ont terminé cette réparation.

Brett Hartt

Membre depuis le 12/04/2010

110 297 Réputation

138 tutoriels rédigés

Équipe

iFixit Membre de l'équipe iFixit

Community

100 membres

7 988 tutoriels rédigés

I have 2 remote controllers of X box one which is not working.

ravi.gopalakrishnan - Réponse

Voir les statistiques:

Dernières 24 heures : 2

7 derniers jours : 9

30 derniers jours : 31

Total : 14,338