Aller au contenu principal

Xbox One S Case Replacement

Ce dont vous avez besoin

  1. Xbox One S Case Replacement, Case: étape 1, image 1 de 1
    • Flip the Xbox One S so that the bottom of the case is facing upward.

  2. Xbox One S Case Replacement: étape 2, image 1 de 1
    • Begin by working at the case on the rear where the warranty sticker is located. Insert the plastic opening tool into the gap between the bottom of the case and the grated top side. Then find the clips in between that hold the case in place. Use the opening tool to pop the clips out. The best method is to pry the black case away from the bottom.

    • Use the opening tool to pop the clips out. The best method is to pry the black case away from the bottom.

    • You will hear clicking sounds when you are prying the case open. It may be fairly difficult to remove the bottom.

    • It's possible that the clips may break when you remove the bottom from the case.

    • We recommend starting at the back where the warranty sticker is located. Pry along the rear edge until all clips are free. From there do each side. When three sides are free start at the end of the front opposite the sync button. Be cautious and take your time and all should separate without any damage.

    Be careful not to damage the pairing button on this part

    David - Réponse

    Important!!

    You've to start from the back corner where is the information label, because there is a main clip behind a warranty sticker

    Cristian Ramirez - Réponse

    They should add this to the guide! I didnt know that, and did some minor damage to the bottom piece where that main clip is.

    I dont mind because it's my own Xbox, but what if it belonged to a customer?

    Charles Jackson -

    They should add this to the guide! I didnt know that, and did some minor damage to the bottom piece where that main clip is.

    I dont mind because it's my own Xbox, but what if it belonged to a customer?

    💯% same opinion!

    profnussecke42o -

    This was hard! I tried using plastic pry tools, but they did not work. A metal tool did, but make sure to watch a video or two, to see what you actually are dealing with. After the videos it went quite smoothly.

    Peterdk - Réponse

    I legitimately cannot open the case where the warranty sticker is, ive tried everything, im resorting to a fork to try and open this

    Sohail ツShah - Réponse

  3. Xbox One S Case Replacement: étape 3, image 1 de 1
    • Once all of the clips are opened, remove the bottom part of the case.

  4. Xbox One S Case Replacement: étape 4, image 1 de 2 Xbox One S Case Replacement: étape 4, image 2 de 2
    • Use a T10 Torx screwdriver to remove the six green 50 mm long screws from the metal case labeled F1 through F6.

    My F3 isn't coming out. The screwdriver isn't sitting tight like it is for the other ones. Any idea on how to fix that?

    ben mccord - Réponse

  5. Xbox One S Case Replacement: étape 5, image 1 de 2 Xbox One S Case Replacement: étape 5, image 2 de 2
    • Gently separate the interior case from the white exterior case using the appropriate method.

    • Pry the white plastic sides outwards at the rear to separate from the plastic I/O shield

    Essential tip: be sure to slide the metal housing backward, away from the from of the case as pictured above, rather than upward. If not, you can easily break off the teeny momentary switches on the IR blaster board!

    Mark Ross - Réponse

    “appropriate method is not descriptive like Mr. Ross’s comment. The original poster should edit the description to ensure people do in fact remove the box from the case appropriately. I would also add arrows to the picture.

    Ryan A - Réponse

    ____________⬆️

    ↖️Yes! I see it the same way!↗️

    ⬅️Arrows are always a good thing!➡️

    ↙️Can't do anything wrong with them! ↘️

    ____________⬇️

    😅😅

    profnussecke42o -

    I didn't realize that metal ribbon was connecting the case to the console and I yanked it w out realizing it was there. How o I get a replacement?

    Jerianna Mike - Réponse

Conclusion

To reassemble your device, follow these instructions in reverse order.

36 autres ont terminé cette réparation.

Christopher Chen

Membre depuis le 04/26/17

621 Réputation

2 tutoriels rédigés

Équipe

Cal Poly, Team S22-G3, Livingston Spring 2017 Membre de l'équipe Cal Poly, Team S22-G3, Livingston Spring 2017

CPSU-LIVINGSTON-S17S22G3

4 membres

56 tutoriels rédigés

5 commentaires

I struggled with the retention tabs the first time I opened the Xbox S. I dabbed a little Armor All on a Qtip and coated both sides of tabs with a little. Popped right open the second time, wiped Armor All on the fan blades as well to minimize dust collection.

Mike DePedro - Réponse

Hi!

Great review of the process! I have a question, having stripped down an rebuilt an XBox One S to extract a 500 yuan note and two peties my 7 year old inserted in the CD/DVD slop, as well as a DOA DVD drive the power switch is not working. It works if I short the contact but there appears to be a square hole in the back of the power switch (the x box logo)

Should there be a conducting contact in the back of the switch and if so, is it simply a square lump of steel or is it tapered? Would like the dimensions please.

Many thanks for taking time to reply!

Dr B

Dr John C Bullas

Southampton UK

john.bullas - Réponse

Hi can u fit a core i5 apple gen in Xbox one s case

Aayan Beast - Réponse

Excuse me but is there an everyday item that I can use to open the bottom of my Xbox one s with?

Brody Luce - Réponse

CAUTION: Sheared off power and pairing switches when attempting to affix to panel.

Mark - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 19

7 derniers jours : 161

30 derniers jours : 640

Total : 62,533