Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
-
Commencez par travailler sur l'arrière du boîtier, là où est situé le sticker de garantie. Insérez un outil d'ouverture en plastique dans l'espace entre le bas du boîtier et le côté supérieur avec la grille. Puis trouvez les clips entre les deux qui maintiennent le boîtier en place.
-
Avec l'outil d'ouverture en plastique, désenclenchez les clips. La meilleure méthode est de faire levier sur le boîtier noir, vers le haut.
-
-
-
-
Pour remplacer le disque dur, retournez la console et retirez les deux vis torx T10 de 10 mm, numérotées C3 et C4, depuis l'arrière de la Xbox One S.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
To remove the optical disc drive, remove the silver 10 mm T-10 Torx screw labeled "C4."
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pull the disc drive slightly off the motherboard and disconnect the plastic connectors from the motherboard.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
To replace the motherboard you must remove the three silver 10 mm T-10 Torx screws labelled "C1," "C2," and "C6."
-
Remove the four black 8 mm T-8 Torx screws lablelled "A1," "A2," "A3," and "A4."
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Locate the rectangular silver clamp on the opposite corner of the power block.
-
Remove the black bracket near the fan.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Grab the clamp with the tweezers. Pull the clamp upward, away from the silver casing. Jiggle it back and forth like a tooth if necessary.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the four black 8 mm T-9 Torx screws labeled "E1," "E2," "E3," and "E4."
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the three black 8 mm T-9 Torx screws labeled "D1," "D2," and "D3" to remove the Mediatek board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Now that the clamp is removed, gently lift the motherboard from its edges out from the metal casing. The motherboard should come out with ease.
-
Annulation : je n'ai pas terminé ce tutoriel.
55 autres ont terminé cette réparation.
10 commentaires
This guide is really missing alot between steps 13 and 14. There are two black panels that have to be removed(they’re in the teardown guide). One is on the front with with screws E1 ,E2, E3, E4. And theres another panel on the side with screws D1, D2, D3. Finally there are two more screws on the bottom that hold down the motherboard B1, and B2. Theres Also a black from in between the Fan and case that slides off too.
Yep, I was using this guide and realized that it is missing a few vital steps. Thank you Nathan.
If you have a multimeter could you please test the test points around the board and give me a list of a voltages?
fantastic! only issues that are missing, are mentioned in the comments above. I´d like to include that most of the exterior hardcase clips are made to be HELD in place. Which is why it´s a nuisanse to remove. So, newcomers be careful with it. otherwise you´ll easily break it.
Son los mejores