Réparez vos affaires Communauté Boutique

Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement

Introduction

This replacement consists of learning how to disassemble an Xbox One Wireless Controller and replace the Bumpers. This guide will be showing the replacement of the left bumper but the same steps can be applied to replace the right bumper. It is common for these bumpers to get damaged and lose usability quickly, especially if the controller is used frequently for gaming. Many games require the use of these bumpers in order to perform important tasks pertinent to the game. This replacement guide will walk you through a step-by-step process of disassembling the Xbox controller, removing the bumpers, and replacing them.

Ce dont vous avez besoin

  1. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement, Bumper: étape 1, image 1 de 1

    • Remove the battery cover.

    • Remove batteries.

    Modifier

  2. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: étape 2, image 1 de 3 Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: étape 2, image 2 de 3 Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: étape 2, image 3 de 3

    • Grip the controller firmly to remove the side handle cover.

    • Use a flathead screwdriver or a spudger to wedge between the seams of the front to the side handle of the controller.

    • Move the flathead screwdriver all the way around the side plates seam and push the plate forward.

    Modifier

  3. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: étape 3, image 1 de 2 Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: étape 3, image 2 de 2

    • Use a screwdriver and punch a hole directly in the center label. There you will find a hidden screw.

    • Remove the five 10mm screws located on the back of the controller using a T8 screwdriver.

    Modifier

  5. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: étape 4, image 1 de 2 Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: étape 4, image 2 de 2

    • Remove the backplate.

    Modifier

  6. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: étape 5, image 1 de 2 Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: étape 5, image 2 de 2

    • Remove the faceplate.

    Modifier

  7. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: étape 6, image 1 de 3 Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: étape 6, image 2 de 3 Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: étape 6, image 3 de 3

    • Remove the cover piece surrounding the Xbox button off of its pegs.

    • Firmly hold controller and push cover piece up from the pegs.

    • Press the Xbox button down to assist in the unclipping of the piece.

    Modifier

  8. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: étape 7, image 1 de 2 Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: étape 7, image 2 de 2

    • Remove the broken bumper by unclipping it from its pegs.

    • Hold the controller firmly and push the bumper piece up from its pegs to unclip.

    Modifier

  9. Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: étape 8, image 1 de 3 Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: étape 8, image 2 de 3 Xbox One Wireless Controller Model 1537 (Left) Bumper Replacement: étape 8, image 3 de 3

    • Align the replacement bumper onto the pegs, push gently and click into place.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

19 autres ont terminé cette réparation.

Auteur

avec 2 autres contributeurs

Cristyne Ramirez

Membre depuis le 01/24/18

571 Réputation

1 tutoriel rédigé

Badges: 9

+ 6 badges supplémentaires

Équipe

USF Sarasota-Manatee, Team S1-G1, Stewart Spring 2018 Membre de l'équipe USF Sarasota-Manatee, Team S1-G1, Stewart Spring 2018

USFSM-STEWART-S18S1G1

15 membres

25 tutoriels rédigés

2 commentaires

On my controller the screws were T8 security type, so you'll need bits with a hole in the middle

Sean H - Réponse

Is there a way to do this without removing all of the front and grip.

Alan Marantos - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 16

7 derniers jours : 128

30 derniers jours : 645

Total : 47,186