Aller au contenu principal

Introduction

Use this guide to remove the ambient light sensor in your Xiaomi Redmi 2 for repair or replacement.

Pièces

Aucune pièce spécifiée.

  1. Use the flat end of the spudger to remove the back panel from the mid-frame and front body. Use the flat end of the spudger to remove the back panel from the mid-frame and front body.
    • Use the flat end of the spudger to remove the back panel from the mid-frame and front body.

  2. Insert your finger into the curved opening of the mid-frame.
    • Insert your finger into the curved opening of the mid-frame.

    • Lift the battery and remove.

  3. Remove the SIM and/or memory cards if present.
    • Remove the SIM and/or memory cards if present.

    • Remove twelve 3.4 mm Phillips #000 screws securing the mid-frame to the front body.

  4. Slide the spudger between the mid-frame and front body, gradually prying the two bodies apart as you slide the spudger around the perimeter of the phone.
    • Slide the spudger between the mid-frame and front body, gradually prying the two bodies apart as you slide the spudger around the perimeter of the phone.

  5. Remove the 3.4 mm Phillips #000 screw that holds the motherboard to the front body.
    • Remove the 3.4 mm Phillips #000 screw that holds the motherboard to the front body.

    • Keep this screw separate from the initial twelve.

  6. Using one prong of the tweezers, pry back the brown clip located on top of the LCD ribbon connector. Using one prong of the tweezers, pry back the brown clip located on top of the LCD ribbon connector.
    • Using one prong of the tweezers, pry back the brown clip located on top of the LCD ribbon connector.

  7. Using one prong of the tweezers, pry the ribbon clip away from the motherboard. Using one prong of the tweezers, pry the ribbon clip away from the motherboard.
    • Using one prong of the tweezers, pry the ribbon clip away from the motherboard.

  8. Lift and  hinge the motherboard with your fingers. Lift and  hinge the motherboard with your fingers.
    • Lift and hinge the motherboard with your fingers.

  9. Using one prong of the tweezers, lift and pry back the metal clip positioned over the front proximity sensor ribbon connector. Using one prong of the tweezers, lift and pry back the metal clip positioned over the front proximity sensor ribbon connector.
    • Using one prong of the tweezers, lift and pry back the metal clip positioned over the front proximity sensor ribbon connector.

  10. Using the tweezers, pull the antenna connector from the motherboard. Using the tweezers, pull the antenna connector from the motherboard.
    • Using the tweezers, pull the antenna connector from the motherboard.

  11. Lift the motherboard out of the front cover and set aside.
    • Lift the motherboard out of the front cover and set aside.

  12. Using one prong of the tweezers, lift and loosen the edge of the ambient light sensor from the motherboard.
    • Using one prong of the tweezers, lift and loosen the edge of the ambient light sensor from the motherboard.

  13. Using your fingers, gently pull out the ambient light sensor.
    • Using your fingers, gently pull out the ambient light sensor.

Conclusion

To reassemble your device, follow these instructions in reverse order.

17 autres ont terminé cette réparation.

Alicia Brenner

Membre depuis le 01/10/2015

3 509 Réputation

5 tutoriels rédigés

Équipe

USF Tampa, Team 1-3, Leahy Fall 2015 Membre de l'équipe USF Tampa, Team 1-3, Leahy Fall 2015

USFT-LEAHY-F15S1G3

2 membres

5 tutoriels rédigés

Un commentaire

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 2

30 derniers jours : 7

Total : 5,018