Aller au contenu principal
Aide

Nintendo DSi Top LCD Screen Replacement

En cours

En cours

Ce tutoriel est en cours de réalisation. Actualisez-le régulièrement pour découvrir les dernières modifications !

Tutoriel Archivé

Tutoriel Archivé

Ce tutoriel est conservé uniquement à des fins de suivis historiques. Utilisez la version actuelle du tutoriel pour effectuer votre réparation.

Outils incorrects

Outils incorrects

Participez à l'amélioration de ce tutoriel en utilisant les outils adaptés dans les photos et/ou le texte.

Une étape a été sautée

Une étape a été sautée

Oups ! Il manque encore des étapes importantes à ce tutoriel.

  • Auteur: rjcamero
  • Durée estimée : 1 heure
  • Difficulté: Modérée

This guide has been updated by iFixit staff! Read the new, official guide here.

A guide on how to replace the Nintendo DSi top LCD screen.

Étape 1 Top LCD Screen  ¶ 

To make the repair easier, we recommend removing the bottom LCD screen prior to replacing the top LCD screen.

Étape 1 Top LCD Screen  ¶ 

  • To make the repair easier, we recommend removing the bottom LCD screen prior to replacing the top LCD screen.

  • Using a spudger, or similar tool, pry out the 4 square screw covers.

Étape 2  ¶ 

Remove 4 Phillips screws with a #00 Phillips screwdriver.

Étape 2  ¶ 

  • Remove 4 Phillips screws with a #00 Phillips screwdriver.

Étape 3  ¶ 

Place a plastic opening tool between the front panel and top edge of the outer case. Slide the tool along the edge as needed to prop open the case.

Étape 3  ¶ 

  • Place a plastic opening tool between the front panel and top edge of the outer case. Slide the tool along the edge as needed to prop open the case.

  • With the screen facing you, slide the screen side down with your thumbs to separate the screen from the cover.

Étape 4  ¶ 

Remove the antenna from the bottom left of the device.

Étape 4  ¶ 

  • Remove the antenna from the bottom left of the device.

  • Remove the microphone from the top of the frame.

Étape 5  ¶ 

Use a spudger to pry the camera out of its place.

Étape 5  ¶ 

  • Use a spudger to pry the camera out of its place.

Étape 6  ¶ 

Cables for the components in the upper half of the device run through the hinge, which must be carefully disassembled before continuing.

Étape 6  ¶ 

  • Cables for the components in the upper half of the device run through the hinge, which must be carefully disassembled before continuing.

  • Start by pushing the sliding shaft in the hinge on the opposite side of the wires/ribbons.

Étape 7  ¶ 

On the reverse side of the casing, insert the spudger onto the surface of the sliding shaft just left of the LED light channels.

Étape 7  ¶ 

  • On the reverse side of the casing, insert the spudger onto the surface of the sliding shaft just left of the LED light channels.

  • Push the sliding shaft completely through the hinge until it stops and the hinge is released.

Étape 8  ¶ 

The right side of bottom case should separate from the top case when you remove the sliding shaft.

Étape 8  ¶ 

  • The right side of bottom case should separate from the top case when you remove the sliding shaft.

  • Do not pull up too far or the wire hinge may be damaged.

  • Slide the top case to the right to separate the joint.

  • Weave the wires and ribbons through the wire hinge to completely separate the top and bottom casings.

Étape 9  ¶ 

The speakers are soldered to the ribbon cable attached to the upper LCD, so they must be removed at the same time as the LCD. Lift the top LCD out of the plastic frame. Carefully thread the ribbon cable out of the hinge to avoid damaging it.

Étape 9  ¶ 

  • The speakers are soldered to the ribbon cable attached to the upper LCD, so they must be removed at the same time as the LCD.

  • Lift the top LCD out of the plastic frame. Carefully thread the ribbon cable out of the hinge to avoid damaging it.

Étape 10  ¶ 

To remove the speakers, place a flat object underneath and gently pry them off.

Étape 10  ¶ 

  • To remove the speakers, place a flat object underneath and gently pry them off.