Aller au contenu principal
Aide

Asus Eee PC 1005HA Bluetooth Module Replacement

Nécessite plus d'images

Nécessite plus d'images

Quelques images en plus, et les étapes de ce tutoriel seraient claires et nettes.

This guide will provide you with step-by-step instructions to replace a damaged Bluetooth component for Asus Eee PC 1005HA.

  • Auteur: Maged Hanna
  • Durée estimée : 20 minutes
  • Difficulté: Modérée

A faulty Bluetooth Module can cause delayed or no connection to peripheral wireless devices such as mice, headsets, and microphones. If the problem cannot be solved by installing an update, replacement may be necessary. Follow this guide to replace your Bluetooth Module. Note: Before beginning this guide, remove the battery by referring to the Battery Replacement Guide.

Étape 1 Bluetooth Module  ¶ 

Flip the laptop over. Using a Phillips #1 screwdriver, remove the five 5.65 mm screws.

Étape 1 Bluetooth Module  ¶ 

  • Flip the laptop over.

  • Using a Phillips #1 screwdriver, remove the five 5.65 mm screws.

  • The screw that holds the RAM compartment cover may be permanently connected. This screw is the center most screw of the five.

  • Be sure to have a designated place to hold the different sized screws removed in this guide.

Étape 2  ¶ 

Remove the lid to the RAM compartment, if possible. To remove the RAM, depress the tabs that are holding it in. These tabs are bound in red in the picture. Use a spudger to unclip the edges of the cover if necessary.

Étape 2  ¶ 

  • Remove the lid to the RAM compartment, if possible.

  • To remove the RAM, depress the tabs that are holding it in. These tabs are bound in red in the picture.

  • Use a spudger to unclip the edges of the cover if necessary.

  • The battery is shown still attached in the picture, but it should be removed prior to beginning this guide.

Étape 3  ¶ 

Use a Phillips #1 screwdriver to remove one 6.5 mm screw located next to the RAM.

Étape 3  ¶ 

  • Use a Phillips #1 screwdriver to remove one 6.5 mm screw located next to the RAM.

Étape 4  ¶ 

Flip the laptop back over, and open the display. Use a Phillips #1 screwdriver to remove the six 5.5 mm screws on the inside covering.

Étape 4  ¶ 

  • Flip the laptop back over, and open the display.

  • Use a Phillips #1 screwdriver to remove the six 5.5 mm screws on the inside covering.

Étape 5  ¶ 

Detach the five plastic clips holding the upper and lower halves of the laptop together. These can be undone by carefully running a plastic opening tool between the top and bottom casing. There will be an audible audible "click" as the clips come undone. The top plastic is fragile. There are also two miniature LEDs exposed along the top edge of the bottom casing at the bottom right that are easily damaged.

Étape 5  ¶ 

  • Detach the five plastic clips holding the upper and lower halves of the laptop together. These can be undone by carefully running a plastic opening tool between the top and bottom casing. There will be an audible audible "click" as the clips come undone.

  • The top plastic is fragile. There are also two miniature LEDs exposed along the top edge of the bottom casing at the bottom right that are easily damaged.

  • Once the five clips have been undone, carefully remove the upper half of the laptop.

Étape 6  ¶ 

Detach the track pad ribbon by using a plastic opening tool to raise up the black pad.

Étape 6  ¶ 

  • Detach the track pad ribbon by using a plastic opening tool to raise up the black pad.

Étape 7  ¶ 

Detach the Bluetooth wire located below the fan by gently pulling it upward. Detach the Bluetooth wire located below the fan by gently pulling it upward.

Étape 7  ¶ 

  • Detach the Bluetooth wire located below the fan by gently pulling it upward.