Aller au contenu principal
Aide

Motorola Droid 2 Front Panel Replacement

Tutoriel vedette

Tutoriel vedette

L'équipe iFixit trouve ce tutoriel particulièrement réussi.

Replace a shattered front panel on your Droid 2.

This guide will take you through the process of installing a new front panel on your Motorola Droid 2.

Sections

Étape 1 Front Panel  ¶ 

Disconnect the camera button/vibrator connector by prying it straight up off its socket on the speaker board with a spudger.

Étape 1 Front Panel  ¶ 

  • Disconnect the camera button/vibrator connector by prying it straight up off its socket on the speaker board with a spudger.

Étape 2  ¶ 

Remove the large sticker stuck to the inner face of the battery compartment.

Étape 2  ¶ 

  • Remove the large sticker stuck to the inner face of the battery compartment.

Étape 3  ¶ 

Slide the phone open. Lift up the edge of the black plastic rim that includes the speaker board from the side closest to the keypad.

Étape 3  ¶ 

  • Slide the phone open.

  • Lift up the edge of the black plastic rim that includes the speaker board from the side closest to the keypad.

  • Continue lifting the side of the rim until it is almost vertical, and wiggle it free from the back of the LCD assembly.

Étape 4  ¶ 

Remove the EMI shield by releasing the clips shown with the tip of a spudger.

Étape 4  ¶ 

  • Remove the EMI shield by releasing the clips shown with the tip of a spudger.

Étape 5  ¶ 

Remove the five 2.5 mm T3 Torx screws along the outer edge of the slider panel.

Étape 5  ¶ 

  • Remove the five 2.5 mm T3 Torx screws along the outer edge of the slider panel.

Étape 6  ¶ 

Slide the phone until a sixth screw is visible, as shown.

Étape 6  ¶ 

  • Slide the phone until a sixth screw is visible, as shown.

  • Remove the newly revealed 2.5 mm T3 Torx screw.

Étape 7  ¶ 

Continue sliding the phone in the same direction, past its "closed" position, until four more screws are revealed.

Étape 7  ¶ 

  • Continue sliding the phone in the same direction, past its "closed" position, until four more screws are revealed.

  • Remove the four 2.5 mm T3 Torx screws along the outer edge of the slider.

Étape 8  ¶ 

Return the phone to its normal "closed" position.

Étape 8  ¶ 

  • Return the phone to its normal "closed" position.

  • Peel the display ribbon up from the keypad's metal backing.

  • The ribbon cannot be completely removed yet, because it is attached to the back of the LCD.

  • At this point take extra caution as to not tear the ribbon cable.

Étape 9  ¶ 

Insert a spudger between the back and front case of the display assembly, and peel the two ribbon cables off the two adhesive pads along the back case of the display assembly. The location of the pads on the back case is shown.  The top left corner of the case is the corner of the phone shown in the first picture.

Étape 9  ¶ 

  • Insert a spudger between the back and front case of the display assembly, and peel the two ribbon cables off the two adhesive pads along the back case of the display assembly.

  • The location of the pads on the back case is shown. The top left corner of the case is the corner of the phone shown in the first picture.

Étape 10  ¶ 

Use the flat end of a spudger to lift the board that contains the ambient light sensor and display data cable connector out of the screen housing.

Étape 10  ¶ 

  • Use the flat end of a spudger to lift the board that contains the ambient light sensor and display data cable connector out of the screen housing.

Étape 11  ¶ 

Use the tip of a spudger to lift the speaker out of the screen housing. Use the tip of a spudger to lift the speaker out of the screen housing.

Étape 11  ¶ 

  • Use the tip of a spudger to lift the speaker out of the screen housing.

Étape 12  ¶ 

Peel off the black tape to reveal the front panel connector.

Étape 12  ¶ 

  • Peel off the black tape to reveal the front panel connector.

Étape 13  ¶ 

Remove the front panel ribbon cable from the ZIF connector on the board that is attached to the display ribbon.

Étape 13  ¶ 

  • Remove the front panel ribbon cable from the ZIF connector on the board that is attached to the display ribbon.

Étape 14  ¶ 

Flip the phone over and remove the front panel.

Étape 14  ¶ 

  • Flip the phone over and remove the front panel.