Aller au contenu principal
Aide

HP Pavilion zd8000 Top Cover Replacement

  • Auteur: Allie Menard
  • Durée estimée : 15 - 25 minutes
  • Difficulté: Modérée
Sections

Étape 1 Top Cover  ¶ 

With the laptop face-down, remove the eleven 8mm Philips screws. With the laptop face-down, remove the eleven 8mm Philips screws.

Étape 1 Top Cover  ¶ 

  • With the laptop face-down, remove the eleven 8mm Philips screws.

Étape 2  ¶ 

Rotate the laptop 180 degrees so the vents are facing you. Unscrew the four 3mm Philips screws below the vents.

Étape 2  ¶ 

  • Rotate the laptop 180 degrees so the vents are facing you.

  • Unscrew the four 3mm Philips screws below the vents.

Étape 3  ¶ 

Rotate the laptop 90 degrees counter-clockwise. Unscrew the two 3mm Philips screws from the optical drive bay.

Étape 3  ¶ 

  • Rotate the laptop 90 degrees counter-clockwise.

  • Unscrew the two 3mm Philips screws from the optical drive bay.

Étape 4  ¶ 

Flip the laptop over so it is face-up with the trackpad closest to you. Locate the ribbon cable directly above the track pad. Find the black latch at the end of the ribbon cable and unlatch it with a spudger to release it.

Étape 4  ¶ 

  • Flip the laptop over so it is face-up with the trackpad closest to you.

  • Locate the ribbon cable directly above the track pad.

  • Find the black latch at the end of the ribbon cable and unlatch it with a spudger to release it.

Étape 5  ¶ 

Find the ribbon cable on the LED board located at the top of the laptop. You will notice that the ribbon cable is connected to two levels - you will be dealing with the one on the lower level. Find the black latch at the end of the ribbon cable and unlatch it with a spudger to release it.

Étape 5  ¶ 

  • Find the ribbon cable on the LED board located at the top of the laptop.

  • You will notice that the ribbon cable is connected to two levels - you will be dealing with the one on the lower level.

  • Find the black latch at the end of the ribbon cable and unlatch it with a spudger to release it.

Étape 6  ¶ 

Locate the white connector attached to a red and black cable to the right of the LED board. Using tweezers, pull the white connector away from you.

Étape 6  ¶ 

  • Locate the white connector attached to a red and black cable to the right of the LED board.

  • Using tweezers, pull the white connector away from you.

Étape 7  ¶ 

Unscrew the four 8mm Philips screws from the top cover. Unscrew the four 8mm Philips screws from the top cover.

Étape 7  ¶ 

  • Unscrew the four 8mm Philips screws from the top cover.

Étape 8  ¶ 

Rotate the computer 90 degrees clockwise and insert the spudger at the seam above the card reader. While lifting the front end of the top cover, slide the spudger across the seam.

Étape 8  ¶ 

  • Rotate the computer 90 degrees clockwise and insert the spudger at the seam above the card reader.

  • While lifting the front end of the top cover, slide the spudger across the seam.

  • When you have reached the firewire port, it should click open.

Étape 9  ¶ 

Lift the top cover from the left side to remove it completely.

Étape 9  ¶ 

  • Lift the top cover from the left side to remove it completely.