Aller au contenu principal
Aide

Canon Powershot S200 Motherboard Replacement

A besoin de meilleures images

A besoin de meilleures images

De meilleures photos amélioreront ce tutoriel. Aider en proposant de nouvelles photos!

Puces !

Puces !

Une bonne utilisation des balises, de la couleur et/ou du format des puces donnera de la clarté à ce tutoriel !

This guide shows one how to install a new motherboard into the device.

  • Auteur: Orlando Zuniga
  • Durée estimée : 20 - 25 minutes
  • Difficulté: Modérée

The motherboard controls the operations of the camera. Damage to the motherboard requires an entirely new motherboard.

Sections
Outils

Étape 1 Motherboard  ¶ 

Remove the lanyard.

Étape 1 Motherboard  ¶ 

  • Remove the lanyard.

Étape 2  ¶ 

Remove the two 2.3mm screws (underneath the name plate) and two 2.8mm screws (next to the threaded tripod mount) from the bottom face of the camera.

Étape 2  ¶ 

  • Remove the two 2.3mm screws (underneath the name plate) and two 2.8mm screws (next to the threaded tripod mount) from the bottom face of the camera.

  • Be careful to keep track of the different screw sizes as you proceed with this guide.

Étape 3  ¶ 

Remove the single 3.8mm screw from the back face of the camera.

Étape 3  ¶ 

  • Remove the single 3.8mm screw from the back face of the camera.

Étape 4  ¶ 

Remove the two 2.3mm screws from the right face of the camera.

Étape 4  ¶ 

  • Remove the two 2.3mm screws from the right face of the camera.

Étape 5  ¶ 

Remove the two 3.2mm screws (outside edge) and two 3.7mm screws (towards middle) from the left side of the camera body.

Étape 5  ¶ 

  • Remove the two 3.2mm screws (outside edge) and two 3.7mm screws (towards middle) from the left side of the camera body.

Étape 6  ¶ 

Pull the back face panel away from the front end of the body. This may take some wiggling and force.

Étape 6  ¶ 

  • Pull the back face panel away from the front end of the body. This may take some wiggling and force.

Étape 7  ¶ 

Remove the CF card door from the left side of the camera body. Remove the CF card door from the left side of the camera body.

Étape 7  ¶ 

  • Remove the CF card door from the left side of the camera body.

Étape 8  ¶ 

Remove the rubber digital a/v out cap by sliding it out of the groove on the front plate. Remove the rubber digital a/v out cap by sliding it out of the groove on the front plate.

Étape 8  ¶ 

  • Remove the rubber digital a/v out cap by sliding it out of the groove on the front plate.

Étape 9  ¶ 

Remove the front face by sliding it off.

Étape 9  ¶ 

  • Remove the front face by sliding it off.

Étape 10  ¶ 

Remove the rubber seal that goes over the right side of the viewfinder.

Étape 10  ¶ 

  • Remove the rubber seal that goes over the right side of the viewfinder.

Étape 11  ¶ 

Remove the two 3.9mm screws that retain the laminated cooper sheet.

Étape 11  ¶ 

  • Remove the two 3.9mm screws that retain the laminated cooper sheet.

Étape 12  ¶ 

Remove the seven wire connections that connect to the motherboard. Remove the seven wire connections that connect to the motherboard.

Étape 12  ¶ 

  • Remove the seven wire connections that connect to the motherboard.

Étape 13  ¶ 

Remove the single 3.8mm screw that is on the motherboard.

Étape 13  ¶ 

  • Remove the single 3.8mm screw that is on the motherboard.

Étape 14  ¶ 

Carefully remove the motherboard from the main frame of the camera body.

Étape 14  ¶ 

  • Carefully remove the motherboard from the main frame of the camera body.