Aller au contenu principal
Aide

Nikon CoolPix S600 Front and Rear Casing Replacement

A besoin de meilleures images

A besoin de meilleures images

De meilleures photos amélioreront ce tutoriel. Aider en proposant de nouvelles photos!

Conditions préalables manquantes

Conditions préalables manquantes

Ce tutoriel ne donne pas d'informations sur le début de la procédure. Créez un tutoriel de conditions préalables !

Meilleure introduction

Meilleure introduction

Améliorez ce tutoriel en complétant ou modifiant l'introduction.

How to remove the camera's case to access the internal parts of the camera

Étape 1 Front and Rear Casing  ¶ 

With the lens facing forward, remove the one 4.2 mm screw on the bottom right hand corner of the camera.

Étape 1 Front and Rear Casing  ¶ 

  • With the lens facing forward, remove the one 4.2 mm screw on the bottom right hand corner of the camera.

Étape 2  ¶ 

Remove the chrome side cover from the body of the camera.

Étape 2  ¶ 

  • Remove the chrome side cover from the body of the camera.

Étape 3  ¶ 

Remove the four 3.2 mm screws on the bottom of the camera.

Étape 3  ¶ 

  • Remove the four 3.2 mm screws on the bottom of the camera.

Étape 4  ¶ 

Remove the two 3.2 mm screws from the right side of the camera (with lens is facing forward) Remove the one 3.2 mm screw from the left side of the camera (with lens facing foward)

Étape 4  ¶ 

  • Remove the two 3.2 mm screws from the right side of the camera (with lens is facing forward)

  • Remove the one 3.2 mm screw from the left side of the camera (with lens facing foward)

Étape 5  ¶ 

Gently separate the back cover from the body of the camera. The back casing will still be connected to the circuit board by a ribbon

Étape 5  ¶ 

  • Gently separate the back cover from the body of the camera.

  • The back casing will still be connected to the circuit board by a ribbon

Étape 6  ¶ 

Use the tweezers to disconnect the ribbon from the circuit board.

Étape 6  ¶ 

  • Use the tweezers to disconnect the ribbon from the circuit board.

Étape 7  ¶ 

Remove the one 2.6 mm screw from the left side of the camera (with the lens facing forward)

Étape 7  ¶ 

  • Remove the one 2.6 mm screw from the left side of the camera (with the lens facing forward)

Étape 8  ¶ 

Gently separate the front cover from the body of the camera. The front casing will still be connected to the circuit board by a few wires

Étape 8  ¶ 

  • Gently separate the front cover from the body of the camera.

  • The front casing will still be connected to the circuit board by a few wires

Étape 9  ¶ 

Remove the two 3.2 mm screws that hold the flash to the front cover.

Étape 9  ¶ 

  • Remove the two 3.2 mm screws that hold the flash to the front cover.

Étape 10  ¶ 

Use the Spudger to remove the copper colored light bulb clip. Remove the front cover entierly from the camera body. Remove the front cover entierly from the camera body.

Étape 10  ¶ 

  • Use the Spudger to remove the copper colored light bulb clip.

  • Remove the front cover entierly from the camera body.