Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
-
Utilisez une pièce de monnaie pour tourner les deux vis de verrouillage de la batterie de 90 degrés vers la gauche.
-
Enlevez le cache de la batterie.
-
Enlevez la batterie de l'ordinateur en tirant sur la languette en plastique.
-
-
-
Tirez les pattes de déverrouillage du clavier vers vous et soulevez le clavier jusqu'à ce qu'il se détache. Notez que la nappe du clavier est toujours attachée à la carte mère, vous ne pouvez donc pas encore retirer complètement le clavier.
-
Si le clavier ne se détache pas, utilisez un petit tournevis à tête plate pour tourner la vis de verrouillage du clavier (entre les touches F4 et F5) de 180 degrés dans les deux sens et réessayez.
-
Faites pivoter le clavier du côté opposé l'écran et posez-le à l'envers sur la zone du pavé tactile.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two Phillips screws that secure the RAM shield.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Grasp the wire metal bracket on top of the RAM shield and pull upward to remove the shield.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pull up the keyboard connector cable by its clear plastic loop.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a straightened paperclip to manually eject the CD-ROM tray.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the computer over so that the bottom is facing up.
-
Remove the following Torx screws:
-
Four short T8 Torx near the battery compartment.
-
Two long T8 Torx near the hinges.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pull the CD-ROM drive tray partly out.
-
Remove the silver Phillips screw from the plastic casing.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the computer over.
-
Remove the three Phillips screws.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
1) With your fingernails, grasp the locking bar on either side and pull up a small amount (about 1/16" or 2 mm).
-
2) After disengaging the locking bar, slide the cable out of the connector.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Loosen the trackpad clamp by pulling the top piece up slightly, freeing the trackpad ribbon.
-
Slide the orange trackpad ribbon out of the clamp.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Push out the rim of the lower case and pull up on the upper case, grasping it just to the left of the optical drive.
-
Repeat the above step on the upper left corner of the upper case, grasping the bottom left corner of the upper case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Grasp the upper case on either side of the keyboard space and rotate up and away from the screen.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following Phillips screws:
-
Remove the longer Phillips screw from the middle-rear of the modem shield.
-
Remove the three identical Phillips screws, two on either side of the EMI fingers, and the remaining one on the right side of the modem shield.
-
Remove the larger Phillips screw that secures the EMI fingers to the modem board.
-
Remove the EMI fingers.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Peel the modem shield away from the metal framework below, working from the right front and moving to the left.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the Phillips screw from the left side of the modem.
-
Pry up the right side of the modem.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the modem partially out and disconnect the cable on the left side.
-
Annulation : je n'ai pas terminé ce tutoriel.
Une autre personne a terminé cette réparation.
Pièces jointes
Un commentaire
is there a way to upgrade the modem so it works with modern internet feeds?