Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pull the keyboard release tabs toward you and lift up on the keyboard until it pops free.
-
Flip the keyboard over, away from the screen, and rest it face-down on the trackpad area.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the four silver Phillips screws that secure the RAM shield.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pull the keyboard cable up from the logic board, holding the cable as close to the connector as possible.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger or small flathead screwdriver to remove the three rubber feet from the lower case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the three newly-revealed Phillips screws.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger or small flathead screwdriver to pry up the three metal rings that housed the rubber bumpers.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the three Torx screws using a T8 Torx screwdriver.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two 4.5 mm Phillips screws on either sides of the battery contacts.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Push the thin rims of the lower case surrounding the battery compartment in, bending them past the tabs, and then lift up to free that corner of the lower case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
There is a slot on the wall of the battery compartment that locks the lower case in place. Use a small flathead screwdriver to pry out the slot's lower rim and pull up on the lower case to free the slot from the tabs holding it.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Run a spudger along the seam between the lower case and upper case on the front of the computer to free the tabs locking the lower case. Pull up on the lower case and continue to use the spudger as necessary until you hear three distinct clicks.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Continue to run the spudger around the front right corner. There are two tabs on the port side of the computer, one near the front corner and one near the sound-out port.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
There are three tabs over the optical drive that must be released before the lower case can come off. Slide the spudger into the lower case above the optical drive and run it toward the back of the computer until you hear three distinct clicks.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the computer so that the back is facing you and pull the lower case up and toward you until the back tabs pop free.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the small greasy springs with white plastic caps from either side of the battery contacts.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Have patience and follow the directions, the end result is up to you.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following 4 screws from the bottom shield:
-
Two 3 mm Phillips.
-
Two 7.5 mm Phillips.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two Phillips screws securing the DC-In board, removing tape as necessary.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Deroute the cable from around the optical drive, removing tape as necessary.
-
Disconnect the DC-In cable from the logic board and angle the DC-In board out of its compartment.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two 3 mm Phillips screws inside the left edge of the battery tray.
-
Three 3 mm Phillips around the battery compartment.
-
Three 4.5 mm Phillips along the optical drive bezel. (a magnetic screwdriver may help to lift these screws out)
-
One 12 mm Phillips in the lower right corner.
-
Four 14.5 mm Phillips.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn over the computer and open it.
-
Use the flat side of a flathead screwdriver to remove the small magnet covering a screw near the middle of the computer.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following 7 screws from the edges of the keyboard area.
-
Three 2 mm Phillips along the right edge.
-
One 4.5 mm Phillips underneath where the magnet was.
-
One 6 mm Phillips with a small head in the lower left corner.
-
Two 6 mm Phillips with large heads, one in the upper left corner and one in the middle.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Carefully lift the upper case slightly and move it toward the front of the computer to reveal the trackpad connector. Use a spudger or your finger to disconnect the trackpad connector hidden beneath the white plastic tab.
-
After disconnecting the track pad connector, carefully rotate the upper case away from you and rest it against the display.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the sharp end of a spudger to disconnect the speaker cable connector.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Using the sharp end of a spudger, disconnect the connector for the blue and white power cables. Again, be careful to pry up only on the connector.
-
The upper case is now free and can be removed from the computer.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the fifteen 3 mm Phillips screws securing the top shield to the computer.
-
Remove the following 16 screws:
-
Thirteen 3 mm Phillips.
-
One 3 mm Phillips. (actual screw not present in image)
-
Two 4 mm Phillips.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the top shield up from the right side, minding the upper left corner, which may catch on the metal framework.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the RJ-11 cable from the top of the modem.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two Phillips screws at the corners of the modem.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the modem and modem shield from the bottom.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following three screws:
-
Two 3mm Phillips screws.
-
One 7.5 mm Phillips screw.
-
Lift the small plastic retaining bracket up and out of the computer.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Using a spudger, pry up the AirPort/Bluetooth board from the end closest to the hard drive. Be sure to pry against the metal framework, as shown in the picture.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Hold the AirPort/Bluetooth board in one hand and use a spudger to disconnect the two antenna cables.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the AirPort antenna cables off the heat sink and set them aside.
-
Lift the metal restraining bracket from the hard drive and place it aside.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two Phillips screws from the white plastic fingers of the hinge grill.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following 7 screws and 2 nuts from the heat sink:
-
One 3.5 mm Phillips from the lower left corner of the heat sink.
-
Five 6 mm Phillips from around the fan and at the center of the heat sink.
-
One 7.5 mm Phillips at the top right corner of the heat sink.
-
Two 4 mm screw nuts with attached springs from either side of the heat sink.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger to pry the heat sink up on the left side, near the hard drive.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Grasp the heat sink in one hand and lift up the hinge grill in the other hand so that you can remove the heat sink from the computer.
-
Annulation : je n'ai pas terminé ce tutoriel.
2 autres ont terminé cette réparation.