Réparez vos affaires

Droit à la réparation

Boutique

iBook G4 12" 800 MHz-1.2 GHz Bottom Shield Replacement

Rédigé par : iRobot (et 5 autres contributeurs)
  • Commentaires : 23
  • Favoris : 0
  • Réparations terminées : 29

Difficulté

Modérée

Étapes

16

Sections

3

Drapeaux

0

Introduction

The metallic bottom shield protects the logic board from electromagnetic interference.

  1. Use a coin to rotate the battery locking screw 90 degrees clockwise.

    • Use a coin to rotate the battery locking screw 90 degrees clockwise.

    Modifier

  2. Lift the battery out of the computer.

    • Lift the battery out of the computer.

    Modifier

  3. Use a pin (or anything you like) to remove the three rubber feet from the lower case.

    • Use a pin (or anything you like) to remove the three rubber feet from the lower case.

    Modifier

  4. Remove the three newly-revealed Phillips screws.

    • Remove the three newly-revealed Phillips screws.

    Modifier

  5. Use a spudger or small flathead screwdriver to pry up the three metal rings that housed the rubber bumpers.

    • Use a spudger or small flathead screwdriver to pry up the three metal rings that housed the rubber bumpers.

    Modifier

  6. Remove the three Torx screws using a T8 Torx screwdriver.

    • Remove the three Torx screws using a T8 Torx screwdriver.

    • The shorter screw is in the center of the computer.

    Modifier

  7. Le kit d'outils Essentiel

    Les outils les plus utiles dans notre kit le plus compact.

    J'achète

    Le kit d'outils Essentiel

    Les outils les plus utiles dans notre kit le plus compact.

    J'achète

  8. Remove the two Phillips screws on either side of the battery contacts.

    • Remove the two Phillips screws on either side of the battery contacts.

    Modifier

  9. Breathe deeply. Trying times are ahead, but we promise the lower case does come off.

    • Breathe deeply. Trying times are ahead, but we promise the lower case does come off.

    • Push the thin rims of the lower case surrounding the battery compartment in, bending them past the tabs, and then lift up to free that corner of the lower case.

    Modifier

  10. There is a slot on the wall of the battery compartment that locks the lower case in place. Use a small flathead screwdriver to pry out the slot's lower rim and pull up on the lower case to free the slot from the tabs holding it.

    • There is a slot on the wall of the battery compartment that locks the lower case in place. Use a small flathead screwdriver to pry out the slot's lower rim and pull up on the lower case to free the slot from the tabs holding it.

    Modifier

  11. Run a spudger along the seam between the lower case and upper case on the front of the computer to free the tabs locking the lower case. Pull up on the lower case and continue to use the spudger as necessary until you hear three distinct clicks.

    • Run a spudger along the seam between the lower case and upper case on the front of the computer to free the tabs locking the lower case. Pull up on the lower case and continue to use the spudger as necessary until you hear three distinct clicks.

    Modifier

  12. Continue to run the spudger around the front, right corner. There are two tabs on the port side of the computer, one near the front corner and one near the sound-out port.

    • Continue to run the spudger around the front, right corner. There are two tabs on the port side of the computer, one near the front corner and one near the sound-out port.

    Modifier

  13. There are three tabs over the optical drive that must be released before the lower case can come off. Slide the spudger into the lower case above the optical drive and run it toward the back of the computer until you hear three distinct clicks.

    • There are three tabs over the optical drive that must be released before the lower case can come off. Slide the spudger into the lower case above the optical drive and run it toward the back of the computer until you hear three distinct clicks.

    Modifier

  14. Once the front and sides of the lower case are free, turn the computer so that the back is facing you and pull the lower case up and away from you until the back tabs pop free.

    • Once the front and sides of the lower case are free, turn the computer so that the back is facing you and pull the lower case up and away from you until the back tabs pop free.

    • it may be helpful to jiggle the case up and down.

    Modifier

  15. Remove the small greasy springs with white plastic caps from either side of the battery contacts.

    • Remove the small greasy springs with white plastic caps from either side of the battery contacts.

    Modifier

  16. Remove the 4 Phillips screws from the bottom shield.

    • Remove the 4 Phillips screws from the bottom shield.

    • The two longer screws are along the computer's edge, near the ports.

    Modifier

  17. Lift the bottom shield off.

    • Lift the bottom shield off.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

29 autre(s) ont terminé cette réparation.

Pièces jointes

Auteur

avec 5 autres contributeurs

iRobot

Membre depuis le 24/09/2009

1 Réputation

648 tutoriels rédigés

Badges: 35

+ 32 badges supplémentaires

0 commentaires

Ajouter un commentaire

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 0

7 derniers jours : 1

30 derniers jours : 5

Total : 61,264