Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
-
Utilisez une pièce de monnaie (par exemple 1 centime) pour faire tourner la vis de verrouillage de la batterie de 90 degrés dans le sens des aiguilles d'une montre.
-
Sortez la batterie de l'ordinateur en la soulevant.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pull the keyboard release tabs (shown in yellow) toward you and lift up on the keyboard until it pops free.
-
If the keyboard does not come free, use a small flathead screwdriver to turn the keyboard locking screw (shown in orange) 180 degrees in either direction and try again.
-
Flip the keyboard over, away from the screen, and rest it face-down on the trackpad area.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Loosen the four silver Phillips screws that secure the RAM shield.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pull the keyboard cable up from the logic board, holding the cable as close to the connector as possible.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Close the display and flip the computer over.
-
Remove the three hex screws using a T8 Torx screwdriver.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger or small flathead screwdriver to remove the three rubber feet from the lower case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the three newly-revealed Phillips screws.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger or small flathead screwdriver to pry up the three metal rings that housed the rubber bumpers.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two Phillips screws on either side of the battery contacts.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Push in the thin rims of the lower case surrounding the battery compartment, bending them past the tabs, and then lift up to free that corner of the lower case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
There is a slot on the wall of the battery compartment that locks the lower case in place. Use a small flathead screwdriver to pry out the slot's lower rim and pull up on the lower case to free the slot from the tabs holding it.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Run a spudger along the seam between the lower case and upper case on the front of the computer to free the tabs locking the lower case. Pull up on the lower case and continue to use the spudger as necessary until you hear three distinct clicks.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Continue to run the spudger around the front, right corner. There are two tabs on the port side of the computer, one near the front corner and one near the sound-out port.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
There are three tabs over the optical drive that must be released before the lower case can come off. Slide the spudger into the lower case above the optical drive and run it toward the back of the computer until you hear three distinct clicks.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the computer so that the back is facing you and pull the lower case up and toward you until the back tabs pop free.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the small greasy springs with white plastic caps from either side of the battery contacts.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following 10 screws from the bottom shield:
-
Six 3 mm Phillips
-
Three 7.5 mm Phillips
-
One 14 mm Phillips
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the single Phillips screw securing the DC-In board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the DC-In cable from the adhesive attaching it to the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the DC-In cable from the logic board.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following 11 screws from the bottom of the computer:
-
Three 3 mm Phillips around the battery compartment.
-
Three 4.5 mm Phillips along the optical drive bezel. (a magnetic screwdriver may help to lift these screws out)
-
One 12 mm Phillips in the lower right corner.
-
Four 14.5 mm Phillips.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn over the computer and open it.
-
Remove the 3 Phillips screws from the edges of the keyboard area.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the upper case and use a spudger or your finger to disconnect the trackpad connector hidden beneath the white plastic tab.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the upper case enough to disconnect the blue and white power cable from the logic board. Using your fingernails, carefully pry the connector from its socket.
-
Carefully disconnect the multicolored speaker cable from the logic board in the same fashion.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following 16 screws:
-
Thirteen 3 mm Phillips.
-
One 3 mm Phillips.
-
Two 4 mm Phillips.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the top shield up from the right side, minding the upper left corner which may catch on the metal framework.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two Phillips screws at the corners of the modem.
-
Remove the two Phillips screws at the corners of the modem.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger to pry the modem up from the end nearest the AirPort card to separate its connector from a socket on the logic board.
-
Use your hands to seperate the modem from the modem shield.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the RJ-11 cable from the end of the modem.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the three 3 mm Phillips screws securing the AirPort card bracket to the framework.
-
Lift the AirPort card bracket up and out of the computer.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two 3 mm Phillips screws securing the AirPort card to the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Using a spudger, pry up on the AirPort card from the end nearest the hard drive to separate the connector from the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger to disconnect the two antenna cables from the AirPort card.
-
Remove the AirPort card from the computer and set it aside.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
De-route the antenna wires from above the heat sink, around the RAM socket, and below the optical drive.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the computer over.
-
Disconnect the inverter cable from the logic board and deroute it from the metal framework, removing tape as necessary.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the computer back over.
-
Use the black plastic loop to disconnect the display data cable from the logic board.
-
Deroute the microphone and display data cables from the metal framework, removing tape as necessary.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the microphone cable at the front of the computer, between the left side of the hard drive and the metal framework.
-
Deroute the microphone and display data cables from the metal framework, removing tape as necessary.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Support the display with one hand and remove the single Phillips screw on either side of the hinge (two screws total).
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the display up and tilt it backwards, freeing it from the two metal alignment posts holding the hinges in place, and slide it away from you.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a 1.5 mm hex screwdriver to remove the two hex screws on either side of the display (four screws total).
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use your thumbs to slightly separate the rear bezel from the front bezel.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Insert the flat end of a spudger into the gap between the front and rear bezels.
-
Rotate your spudger until it is parallel to the front face of the display.
-
Run the spudger around the perimeter of the display to separate the rear bezel from its retaining clips.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the pieces of readily removable tape from around the perimeter of the display.
-
Carefully remove the aluminum tape covering the display data cable connection.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the single screw inserted through the piece of EMI tape near the bottom edge of the display.
-
Use the tip of a spudger to remove the small washer under the screw you just removed.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Peel the aluminum/EMI tape off the cast aluminum frame of the clutch hinges.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two Phillips screws securing each side of the LCD to the clutch hinge frame (four screws total).
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the second of the two Phillips screws securing the clutch cover to the cast aluminum frame of the clutch hinges.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pull the clutch cover away from the front of the display.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the pieces of tape covering the display data and microphone cables near the bottom edge of the display.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the display data cable by pulling its connector away from the socket on the LCD.
-
Remove the display data cable from the display.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the tip of a spudger to lift the microphone out of the front bezel.
-
De-route the microphone cable from around the top and side of the display.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two pieces of tape covering the inverter/AirPort cables along the lower edge of the display.
-
Carefully peel the inverter cable ground strap off the cast aluminum frame of the clutch hinges.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the backlight cable from the inverter.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the single Phillips screw securing the reed switch board to the front bezel.
-
Carefully lift the reed switch board off the metal frame of the clutch hinges.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two Phillips screws securing the right AirPort antenna to the clutch hinge frame.
-
Carefully lift the right AirPort antenna off the clutch hinge frame.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two Phillips screws securing the left AirPort antenna to the clutch hinge frame.
-
Carefully lift the left AirPort antenna off the clutch hinge frame.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the flat end of a spudger to remove the antenna board from the front bezel.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the single Phillips screw securing the front bezel to the middle of the cast aluminum clutch hinge frame.
-
Carefully bend the front display bezel away from the clutch hinges as you slide the two AirPort antennas out from under the clutch hinge frame.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
While pulling the inverter cable away from its socket on the inverter board, use the tip of a spudger to push the connector out of its socket.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the six Phillips screws securing the clutch hinges to the front display bezel.
-
Lift the clutch hinges off the front display bezel.
-
Annulation : je n'ai pas terminé ce tutoriel.
Une autre personne a terminé cette réparation.