Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
-
Utilisez une pièce de monnaie (par exemple 1 centime) pour faire tourner la vis de verrouillage de la batterie de 90 degrés dans le sens des aiguilles d'une montre.
-
Sortez la batterie de l'ordinateur en la soulevant.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pull the keyboard release tabs (shown in yellow) toward you and lift up on the keyboard until it pops free.
-
If the keyboard does not come free, use a small flathead screwdriver to turn the keyboard locking screw (shown in orange) 180 degrees in either direction and try again.
-
Flip the keyboard over, away from the screen, and rest it face-down on the trackpad area.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Loosen the four silver Phillips screws that secure the RAM shield.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pull the keyboard cable up from the logic board, holding the cable as close to the connector as possible.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Close the display and flip the computer over.
-
Remove the three hex screws using a T8 Torx screwdriver.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger or small flathead screwdriver to remove the three rubber feet from the lower case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the three newly-revealed Phillips screws.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger or small flathead screwdriver to pry up the three metal rings that housed the rubber bumpers.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two Phillips screws on either side of the battery contacts.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Push in the thin rims of the lower case surrounding the battery compartment, bending them past the tabs, and then lift up to free that corner of the lower case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
There is a slot on the wall of the battery compartment that locks the lower case in place. Use a small flathead screwdriver to pry out the slot's lower rim and pull up on the lower case to free the slot from the tabs holding it.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Run a spudger along the seam between the lower case and upper case on the front of the computer to free the tabs locking the lower case. Pull up on the lower case and continue to use the spudger as necessary until you hear three distinct clicks.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Continue to run the spudger around the front, right corner. There are two tabs on the port side of the computer, one near the front corner and one near the sound-out port.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
There are three tabs over the optical drive that must be released before the lower case can come off. Slide the spudger into the lower case above the optical drive and run it toward the back of the computer until you hear three distinct clicks.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the computer so that the back is facing you and pull the lower case up and toward you until the back tabs pop free.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the small greasy springs with white plastic caps from either side of the battery contacts.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following 10 screws from the bottom shield:
-
Six 3 mm Phillips
-
Three 7.5 mm Phillips
-
One 14 mm Phillips
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the single Phillips screw securing the DC-In board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the DC-In cable from the adhesive attaching it to the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the DC-In cable from the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following 11 screws from the bottom of the computer:
-
Three 3 mm Phillips around the battery compartment.
-
Three 4.5 mm Phillips along the optical drive bezel. (a magnetic screwdriver may help to lift these screws out)
-
One 12 mm Phillips in the lower right corner.
-
Four 14.5 mm Phillips.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn over the computer and open it.
-
Remove the 3 Phillips screws from the edges of the keyboard area.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the upper case and use a spudger or your finger to disconnect the trackpad connector hidden beneath the white plastic tab.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the upper case enough to disconnect the blue and white power cable from the logic board. Using your fingernails, carefully pry the connector from its socket.
-
Carefully disconnect the multicolored speaker cable from the logic board in the same fashion.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following 16 screws:
-
Thirteen 3 mm Phillips.
-
One 3 mm Phillips.
-
Two 4 mm Phillips.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the top shield up from the right side, minding the upper left corner which may catch on the metal framework.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two Phillips screws at the corners of the modem.
-
Remove the two Phillips screws at the corners of the modem.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger to pry the modem up from the end nearest the AirPort card to separate its connector from a socket on the logic board.
-
Use your hands to seperate the modem from the modem shield.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the RJ-11 cable from the end of the modem.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the three 3 mm Phillips screws securing the AirPort card bracket to the framework.
-
Lift the AirPort card bracket up and out of the computer.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two 3 mm Phillips screws securing the AirPort card to the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Using a spudger, pry up on the AirPort card from the end nearest the hard drive to separate the connector from the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger to disconnect the two antenna cables from the AirPort card.
-
Remove the AirPort card from the computer and set it aside.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
De-route the antenna wires from above the heat sink, around the RAM socket, and below the optical drive.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the computer over.
-
Disconnect the inverter cable from the logic board and deroute it from the metal framework, removing tape as necessary.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the computer back over.
-
Use the black plastic loop to disconnect the display data cable from the logic board.
-
Deroute the microphone and display data cables from the metal framework, removing tape as necessary.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the microphone cable at the front of the computer, between the left side of the hard drive and the metal framework.
-
Deroute the microphone and display data cables from the metal framework, removing tape as necessary.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Support the display with one hand and remove the single Phillips screw on either side of the hinge (two screws total).
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the display up and tilt it backwards, freeing it from the two metal alignment posts holding the hinges in place, and slide it away from you.
-
Annulation : je n'ai pas terminé ce tutoriel.
14 autres ont terminé cette réparation.
Pièces jointes
2 commentaires
Smooth as silk Walter. I am changing this to try and address a Black screen problem. After a Optical Drive and HD (OWC Legacy SSD) my machine went from perfect to normal boot then 28-30 secs later, black screen while everything else worked (caps lock light, pulsing sleep light, etc.) Will let you know if this solved the prob as I have a screen harvested years ago from a working iBook of mine.
Thanks
Nothing yet Walter. The past couple of weeks I have dismantled my iBook 14” 1.42 and put it back together a half dozen times or so. I’ve bought parts off of ebay, harvested stuff from my spare iBook and I am certain of this... It still loads as normal as can be. Bright screen, sound, etc. but 38 secs from first desktop view and 28-30 secs after complete load it gets a black screen.
I’ve checked or replaced: RAM, Inverter cable, HD, different display, and more. I’ve tried rushing to the sys prefs and setting it to “no sleep.” I’ve quickly opened a song in Quicktime and it shuts off with the screen goes black.
Any other suggestions from anyone would be great. I really dig my iBook and it was working fine until I replaced the Optical drive (now gone) and at one point I started it up with only the aluminum shields on and it worked fine. Then, after putting the cases back together, nothing since.