Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a coin to rotate the battery locking screw 90 degrees clockwise.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a 1.5 mm hex screwdriver to remove the two hex screws on either side of the display (four screws total).
-
If you don't have a 1.5 mm hex driver, you can probably get these screws out with a T6 Torx screwdriver. However, if you use a T6 Torx driver you'll be more likely to strip the screws.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Insert the flat end of a spudger perpendicular to the face of the display into the gap between the front and rear bezels near the upper left corner of the display.
-
Rotate the spudger away from the display to pry the rear bezel off the front bezel.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Run your spudger along the top edge of the front display bezel to evenly separate the two bezels.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Working down from the upper left corner, use the flat end of a spudger to pry the rear bezel away from the left edge of the display.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the flat end of a spudger to pry the rear bezel away from the right edge of the display.
-
If necessary, pry along the bottom edge of the rear bezel to separate it from the display assembly.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Close the display.
-
Remove the several pieces of tape securing the thin metal LCD cover to the display.
-
Carefully remove the piece of foil tape covering the display data cable connection.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the Phillips screw near the right display hinge.
-
Use the tip of a spudger to remove the small spacer under the screw you just removed.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pull the foil/braided pieces of tape off the aluminum frame of the clutch hinges.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two Phillips screws securing the left and right sides of the LCD to the frame of the clutch hinges (four screws total).
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the display data cable by pulling the cable away from the socket on the LCD.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the strip of yellow tape securing the display data cable to the metal LCD frame.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the backlight cable from the inverter.
-
Annulation : je n'ai pas terminé ce tutoriel.
7 autres ont terminé cette réparation.
Un commentaire
Im not sure where they get the difficulty ratings from- I found this to be about a 20 minute job- one word of warning - before you order your screen you need to find out if the connector your model uses is a 20pin (about 1 inch long) or 30pin (about 1 1/2 inches long) This means you need to pop off the case and pull up that little metal foil BEFORE you order. Other than that, the hardest part is probably getting that back light cable back in the hole (and it only goes one way) I used a set of my wife's tweezers, and I use a small flat head eyeglass screwdriver to get the case off.