Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a coin to rotate the battery locking screw 90 degrees clockwise.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pull the keyboard release tabs toward you and lift up on the keyboard until it pops free.
-
Flip the keyboard over, away from the screen, and rest it face-down on the trackpad area.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Push the wire clasp away from the AirPort card and toward the display, then rotate up to free it from the RAM shield.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Grasp the clear plastic tab on the AirPort card and pull toward the display.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Hold the AirPort card in one hand and use your other hand to remove the antenna cable.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the four silver Phillips screws that secure the RAM shield.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Grasp the metal bracket on top of the RAM shield and pull upward to remove the shield.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pull the keyboard cable up from the logic board, holding the cable as close to the connector as possible.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a pin (or anything you like) to remove the three rubber feet from the lower case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the three newly-revealed Phillips screws.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger or small flathead screwdriver to pry up the three metal rings that housed the rubber bumpers.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the three hex screws using a T8 Torx screwdriver (or Allen screws using an Allen key if these are used).
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two Phillips screws on either side of the battery contacts.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Push the thin rims of the lower case surrounding the battery compartment in, bending them past the tabs, and then lift up to free that corner of the lower case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
There is a slot on the wall of the battery compartment that locks the lower case in place. Use a small flathead screwdriver to pry out the slot's lower rim and pull up on the lower case to free the slot from the tabs holding it.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Run a spudger along the seam between the lower case and upper case on the front of the computer to free the tabs locking the lower case. Pull up on the lower case and continue to use the spudger as necessary until you hear three distinct clicks.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Continue to run the spudger around the front, right corner. There are two tabs on the port side of the computer, one near the front corner and one near the sound-out port.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
There are three tabs over the optical drive that must be released before the lower case can come off. Slide the spudger into the lower case above the optical drive and run it toward the back of the computer until you hear three distinct clicks.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Once the front and sides of the lower case are free, turn the computer so that the back is facing you and pull the lower case up and toward you until the back tabs pop free (it may be helpful to jiggle the case up and down).
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the small greasy springs with white plastic caps from either side of the battery contacts.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following 10 screws from the bottom shield:
-
Six 3 mm Phillips
-
Three 7.5 mm Phillips
-
One 14 mm Phillips
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the single Phillips screw securing the DC-In board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the DC-In cable from the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Deroute the cable from around the optical drive, removing tape as necessary, and angle the DC-In board out of its compartment.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following 11 screws from the bottom of the computer:
-
Three 3 mm Phillips around the battery compartment. (Some models may only have two screws.)
-
Three 4.5 mm Phillips along the optical drive bezel. (a magnetic screwdriver may help to lift these screws out)
-
One 11 mm Phillips in the lower right corner. (if present)
-
Four 14.5 mm Phillips.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn over the computer and open it.
-
Remove the 2 Phillips screws (3mm) from the edges of the keyboard area.
-
Remove the 4 mm Phillips screw from the lower left corner.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the upper case and use a spudger or your finger to disconnect the trackpad connector hidden beneath the white plastic tab. Due to model variatons your trackpad connector may be different than the one pictured.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Carefully lift the upper case about half of an inch and move it so that you can access the power and speaker cables.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the upper case enough to disconnect the blue and white power cable from the logic board. Using your fingernails or a dental pick, carefully pry the connector from its socket. Make sure you're pulling only on the connector and not on the socket.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Carefully disconnect the multicolored speaker cable from the logic board. As before, make sure you're pulling only on the connector and not on the socket.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following 16 screws:
-
Thirteen 3 mm Phillips.
-
One 3 mm Phillips. (actual screw not present in image)
-
Two 4 mm Phillips.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the top shield up from the right side, minding the upper left corner, which may catch on the metal framework.
-
If your iBook has Bluetooth, as discussed in the previous step, you will need to slide the antenna through the lower I-shaped hole in the shield before completely removing the shield.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two Phillips screws at the corners of the modem.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the modem and modem shield from the bottom.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the RJ-11 cable from the top of the modem.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the computer over and disconnect the fan cable from the logic board.
-
If present, remove the 4 Phillips screws securing the fan to the metal framework (one screw is hidden by the hand in the image) and lift the fan out of the computer. If no screws are present, continue on.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the computer over and remove the two Phillips screws from the white plastic fingers of the hinge grill.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following 6 screws and 3 nuts from the heat sink:
-
One 2 mm Phillips extending from a finger on the left edge of the heatsink and adjacent the firewire port (not present on some models)
-
Three 3 mm Phillips from around the fan (some models may only have 2 screws).
-
One 3.5 mm Phillips on the left side of the heat sink (not present on some models).
-
One 4.5 mm Phillips at the top right corner of the heat sink.
-
One 6 mm Phillips at the lower left corner of the heat sink.
-
One 4 mm nut from the right side of the heat sink.
-
Two 4 mm screw nuts with attached springs from either side of the heat sink.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger to pry the heat sink up on the left side, near the hard drive.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Grasp the heat sink in one hand and lift up the hinge grill in the other hand so that you can remove the heat sink from the computer.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two Phillips screws securing the white plastic fingers of the I/O bezel to the metal framework.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift up the left side of the computer and slide the I/O bezel away.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Wedge a spudger between the RJ-11 board and the metal framework and slide the board to the left, off of the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the microphone cable at the front of the computer, between the left side of the hard drive and the metal framework.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the black plastic loop to disconnect the display data cable from the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the orange optical drive ribbon from the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
1) With your fingernails, grasp the locking bar on either side and pull up a small amount (about 1/16" or 2 mm).
-
2) After disengaging the locking bar, slide the cable out of the connector.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Release the optical drive ribbon clamp as described above. Slide the optical drive ribbon out of its connector.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Tilt the computer up and disconnect the orange hard drive ribbon cable from the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the four Phillips screws securing the hard drive to the metal framework.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the hard drive up, carefully guiding the cable through the slot in the lower case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the single Phillips screw securing the logic board to the metal framework.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Close the display and flip the computer over.
-
Remove the following 8 screws:
-
Four 4 mm Phillips.
-
One 3.5 mm Phillips near the sleep light connector (may not be in your specific model).
-
One 3 mm Phillips with a large head in the lower left corner.
-
One wide 4 mm Phillips.
-
One 3 mm Phillips.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the inverter and sleep light cables from the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the logic board far enough to access and disconnect the battery connector.
-
Annulation : je n'ai pas terminé ce tutoriel.
18 autres ont terminé cette réparation.
Pièces jointes
2 commentaires
First of all, outstanding! I couldn't have done it otherwise. I especially liked the photography. I am a pro in that field and I know the good stuff when I see it.
I just have a few small suggestions.
1) You might want to warn about grounding for rank amateurs like me.
2) The screw sheets were fantastic but it might help to add the step/s involved. Also I found double sided foam tape was great for keeping the screws in place.
3) When removing the back cover I used kitchen matches camphored at one end as shims as I went along so I would not lose ground as I continued around the bottom cover. I also found a fifth of Jack Daniel's helped to steady my hands and give me patience.
4) The whole thermal compound thing was confusing. I looked up the suggested procedure and didn't know what to do about "the blue pads". I posted a question and got conflicting answers. It would be great if this could get resolved once and for all.
5) You might want to talk about installing the RAM when replacing the logic board
Thanks!