Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Orient the iMac face-side down on a table with the bottom edge facing yourself.
-
Remove the two Phillips screws securing the access door to the bottom grille of your iMac.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the three T8 Torx screws securing the front bezel to the rear case along the lower edge of the iMac.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the computer over.
-
Use your thumbs to press both RAM arms in past the front bezel for enough clearance to lift it off the rear case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
While holding the RAM arms in with your thumbs, lift the lower edge of the front bezel enough to clear the rear case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
Outil utilisé dans cette étape :Plastic Cards$2.99-
Insert a plastic card up into the corner of the air vent slot near the top of the rear case.
-
Push the card toward the top of the iMac to release the front bezel latch.
-
Pull the front bezel away from the rear case.
-
Repeat this process for the other side of the front bezel.
-
If the bezel refuses to release, try pressing the lower edge back onto the rear case and repeat this opening process.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lay your iMac stand-side down on a table.
-
Lift the front bezel from its lower edge and rotate it away from the rest of your iMac, minding the RAM arms that may get caught.
-
Lay the front bezel above the rest of the iMac.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
If necessary, remove the piece of kapton tape wrapped around the microphone and camera connectors.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect both the camera and microphone cables.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Peel the lower EMI shield off the lower edge of the iMac and off the two vertical 4" sections on either side of the iMac.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Tape the lower EMI shield up against the face of the display to keep it out of the way while you work.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two T6 Torx screws securing the display data cable connector to the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
To disconnect the display data cable, grab its connector's black tab and pull it away from the face of the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Peel back the two EMI tape strips from the left and right edges of the display.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the four recessed T10 Torx screws securing the display to the rear case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the lower edge of the display slightly out of the rear case.
-
Disconnect both inverter cables (shown in red) by pulling their connectors toward the bottom edge of your iMac.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the display until it is nearly perpendicular to the rear case.
-
Disconnect the remaining two inverter cables (shown in red) by pulling their connectors toward the top edge of your iMac.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
While holding the display perpendicular to the rear case, pull it upward to peel off the EMI shield stuck to its upper edge.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the hard drive thermal sensor from the logic board by pulling its connector toward the top edge of your iMac.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two T10 Torx screws securing the hard drive bracket to the inverter.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the left edge of the hard drive slightly, then pull it toward the left edge of the iMac.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Rotate the hard drive out of the rear case.
-
Disconnect the SATA data cable by pulling its connector away from the hard drive.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Disconnect the SATA power cable by pulling its connector away from the hard drive.
-
Remove the hard drive from the iMac.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two T8 Torx screws securing the hard drive bracket to the connector side of the hard drive.
-
Remove the hard drive bracket.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two T8 Torx pins from the side of the hard drive.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the flat end of a spudger to pry the hard drive thermal sensor off the adhesive securing it to the hard drive.
-
Annulation : je n'ai pas terminé ce tutoriel.
133 autres ont terminé cette réparation.
4 commentaires
Awesome instructable!
Used this same guide to replace the HDD on an A1207 iMac.
Almost identical except for the positioning of the display cable which is on the right hand side of the logic board.
Only problem was the four Torx screws holding in the display. They are so deeply recessed that I had to buy a set of Torx wrenches with long shafts as the Torx heads in the iFixit kit I have are too short.
Good guide.