Aller au contenu principal

Réparez vos affaires

Droit à la réparation

Boutique

Introduction

This guide shows how to apply display assembly adhesive to an opened iPad.

Pièces

Aucune pièce spécifiée.

  1. Before installing new adhesive, thoroughly clean the display assembly and the frame of all residue. Use tweezers to pull up sections of tape residue.
    • Before installing new adhesive, thoroughly clean the display assembly and the frame of all residue.

    • Use tweezers to pull up sections of tape residue.

    • Use an opening tool or a spudger to scrape residue off. You can use high concentration (over 90%) isopropyl alcohol to soften the adhesive.

    • Remove the residue by wiping in one direction to prevent smearing.

    • Do not scrape with a metal tool, or you will scratch the display assembly's surface.

  2. Lay out the replacement adhesive strips around the display assembly so that they correspond to the correct sides.
    • Lay out the replacement adhesive strips around the display assembly so that they correspond to the correct sides.

  3. Each adhesive strip is encased in four layers of plastic—three on top and one on the bottom. Peel and remove the topmost plastic cling layer from the left adhesive strip.
    • Each adhesive strip is encased in four layers of plastic—three on top and one on the bottom.

    • Peel and remove the topmost plastic cling layer from the left adhesive strip.

    • Peel and remove the bottom plastic liner from the strip.

    • The top of the adhesive strip should still be covered by a colored plastic layer as well as a clear plastic stiffening layer.

    • The bottom of the adhesive strip should now be exposed and sticky.

  4. If there are extra bits of adhesive on the strip that are not required for your particular model of iPad, remove them now. If there are extra bits of adhesive on the strip that are not required for your particular model of iPad, remove them now.
    • If there are extra bits of adhesive on the strip that are not required for your particular model of iPad, remove them now.

  5. Align the left adhesive strip to the left edge of the display assembly. Beginning from one corner, lay the adhesive strip onto the display assembly and press the strip into place. Beginning from one corner, lay the adhesive strip onto the display assembly and press the strip into place.
    • Align the left adhesive strip to the left edge of the display assembly.

    • Beginning from one corner, lay the adhesive strip onto the display assembly and press the strip into place.

  6. Repeat the process with the right adhesive strip. Peel and remove the topmost cling layer from the strip. Peel and remove the bottom liner layer from the strip.
    • Repeat the process with the right adhesive strip.

    • Peel and remove the topmost cling layer from the strip.

    • Peel and remove the bottom liner layer from the strip.

    • Align the adhesive strip to the right edge of the display assembly.

    • Starting from one corner, lay the adhesive strip onto the display assembly and press in place.

  7. Repeat the process for the top adhesive strip. Peel and remove the topmost cling layer from the strip. Peel and remove the bottom liner from the strip.
    • Repeat the process for the top adhesive strip.

    • Peel and remove the topmost cling layer from the strip.

    • Peel and remove the bottom liner from the strip.

    • Align the strip to the top of the display assembly such that the straight adhesive line bridges the gap between the left and right strips.

    • Press the strip in place.

  8. Peel and remove the clear plastic stiffening layer from all three adhesive strip sections. The adhesive strips should still be covered by colored plastic liners. The adhesive strips should still be covered by colored plastic liners.
    • Peel and remove the clear plastic stiffening layer from all three adhesive strip sections.

    • The adhesive strips should still be covered by colored plastic liners.

  9. Continue with the reassembly process until you are ready to seal the device.
    • Continue with the reassembly process until you are ready to seal the device.

  10. Peel and remove the three colored plastic liners to expose the adhesive. Close the device and stack some heavy books on top of it for thirty minutes to help the new adhesive bond. Close the device and stack some heavy books on top of it for thirty minutes to help the new adhesive bond.
    • Peel and remove the three colored plastic liners to expose the adhesive.

    • Close the device and stack some heavy books on top of it for thirty minutes to help the new adhesive bond.

Conclusion

Repair didn’t go as planned? Check out our Answers Community for troubleshooting help.

18 autre(s) ont terminé cette réparation.

Arthur Shi

Membre depuis le 03/01/2018

133 041 Réputation

374 tutoriels rédigés

Équipe

iFixit Membre de l'équipe iFixit

Community

132 membres

13 000 tutoriels rédigés

Thanks, I was able to fix my wife’s shattered digitizer screen on the iPad 6th gen with this guide!

Kevin Chatterton II - Réponse

I managed to get it done, but this was a personal nightmare for me and more difficult than replacing the battery in my ipad. There are too many instruction that say “remove plastic” and I have no idea which layer; there was nothing on the packaging to indicate which side was up or which side was the front and I ended up guessing the wrong direction because it “looked” right, but wasn’t. A simple sticker on the packaging indicating a direction would have removed all of the frustration. I only managed to figure it out by removing all of the plastic so that the sticky side of the adhesive was exposed and then I could finally see how it was supposed to fit and how I was supposed to press down with the other side of the plastic to push the adhesive side into the frame.

twizzlercraze72 - Réponse

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 34

7 derniers jours : 196

30 derniers jours : 820

Total : 9,413