Réparez vos affaires

Droit à la réparation

Pièces & Outils

iPad Pro 9.7" Battery Disconnect

Rédigé par : Arthur Shi (et 2 autres contributeurs)
  • Commentaires : 2
  • Favoris : 0

Difficulté

Modérée

Étapes

6

Sections

1

Drapeaux

1

Prerequisite Only

Conditions préalables uniquement

Notez qu'il ne s'agit que de conditions préalables pour d'autres tutoriels.

Introduction

Prerequisite only guide. Shows how to disconnect the battery for the iPad Pro 9.7".

  1. Remove the eleven 1.3 mm Phillips screws securing the EMI shield.

    • Remove the eleven 1.3 mm Phillips screws securing the EMI shield.

    Traduire

  2. Apply a heated iOpener to the EMI shield on the logic board for one minute.

    • Apply a heated iOpener to the EMI shield on the logic board for one minute.

    Traduire

  4. Lift the logic board EMI shield, starting at the edge nearest the top of the iPad. Slowly peel the EMI shield up from the logic board. This takes a bit of force due to the many tiny clips securing the shield, and the shield may deform slightly. That's okay—try to keep the deformation to a minimum, and it will lay flat when reinstalled and screwed down.

    • Lift the logic board EMI shield, starting at the edge nearest the top of the iPad.

    • Slowly peel the EMI shield up from the logic board.

    • This takes a bit of force due to the many tiny clips securing the shield, and the shield may deform slightly. That's okay—try to keep the deformation to a minimum, and it will lay flat when reinstalled and screwed down.

    • Remove the logic board EMI shield.

    Traduire

  5. If the EMI shield has any sharp protrusions after removal, you should flatten them before reinstalling the shield. Squeeze the sharp protrusion with a pair of pliers to flatten it. Repeat the process for all sharp protrusions along the edges of the EMI shield.

    • If the EMI shield has any sharp protrusions after removal, you should flatten them before reinstalling the shield.

    • Squeeze the sharp protrusion with a pair of pliers to flatten it.

    • Repeat the process for all sharp protrusions along the edges of the EMI shield.

    Traduire

  6. Remove the 1.8 mm Phillips screw securing the battery connector.

    • Remove the 1.8 mm Phillips screw securing the battery connector.

    Traduire

  7. Disconnect the battery by inserting a Battery Blocker underneath the logic board to isolate it from the battery's contacts. Insert the Battery Blocker at a slight angle first with one side under the logic board, then slide the rest in over the battery contacts. This may require carefully applied force as the logic board has adhesive holding it onto the case.

    • Disconnect the battery by inserting a Battery Blocker underneath the logic board to isolate it from the battery's contacts.

    • Insert the Battery Blocker at a slight angle first with one side under the logic board, then slide the rest in over the battery contacts.

    • This may require carefully applied force as the logic board has adhesive holding it onto the case.

    • Unless specified otherwise, leave the Battery Blocker in place until you have completed your repairs.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

Auteur

avec 2 autres contributeurs

Arthur Shi

Membre depuis le 03/01/2018

84 624 Réputation

263 tutoriels rédigés

Badges: 45

+ 42 badges supplémentaires

Équipe

iFixit Membre de l'équipe iFixit

Community

108 membres

9 978 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 0

Total : 31