Réparez vos affaires Communauté Boutique

iPhone 7 Rear Case Battery Removal

Conditions préalables uniquement
Ce tutoriel est uniquement destiné à être utilisé comme prérequis d'autres tutoriels. Il ne se suffit pas à lui-même.

Introduction

Prereq only for battery removal when replacing the rear case.

Ce dont vous avez besoin

  1. iPhone 7 Rear Case Battery Removal, Rear Case Battery: étape 1, image 1 de 2 iPhone 7 Rear Case Battery Removal, Rear Case Battery: étape 1, image 2 de 2

    • Use a pair of tweezers with blunt tips to peel back one of the adhesive strips on the lower edge of the battery.

    Traduire

  2. iPhone 7 Rear Case Battery Removal: étape 2, image 1 de 2 iPhone 7 Rear Case Battery Removal: étape 2, image 2 de 2

    • Use a pair of tweezers with blunt tips to peel back the other adhesive strip on the lower edge of the battery.

    Traduire

  4. iPhone 7 Rear Case Battery Removal: étape 3, image 1 de 3 iPhone 7 Rear Case Battery Removal: étape 3, image 2 de 3 iPhone 7 Rear Case Battery Removal: étape 3, image 3 de 3

    • Try to keep the strips flat and unwrinkled during this procedure; wrinkled strips will stick together and break instead of pulling out cleanly.

    • Slowly pull one battery adhesive tab away from the battery, toward the bottom of the iPhone.

    • Pull steadily, maintaining constant tension on the strip until it slips out from between the battery and the rear case. For best results, pull the strip at a 60º angle or less.

    • The strip will stretch to many times its original length. Continue pulling and re-grab the strip near the battery if necessary.

    Traduire

  5. iPhone 7 Rear Case Battery Removal: étape 4, image 1 de 3 iPhone 7 Rear Case Battery Removal: étape 4, image 2 de 3 iPhone 7 Rear Case Battery Removal: étape 4, image 3 de 3

    • Repeat the previous step for the second strip.

    • Hold down the battery as you remove the second strip, or the strip may fling the battery when it separates from the case.

    • If you removed both adhesive strips successfully, skip the next step.

    • Otherwise, if either of the adhesive strips broke off underneath the battery and could not be retrieved, continue with the next step below.

    Traduire

  6. iPhone 7 Rear Case Battery Removal: étape 5, image 1 de 2 iPhone 7 Rear Case Battery Removal: étape 5, image 2 de 2

    • If you successfully removed both adhesive strips, move on to the next step. Otherwise, you will need to pry the battery from the rear case.

    • Prepare an iOpener and apply it to the back of the rear case, directly over the battery. Alternatively, you can apply heat using a heat gun or hair dryer.

    • After about a minute, remove the iOpener, flip the phone over and use a plastic card to break up any remaining adhesive behind the battery.

    • Avoid bending the battery. Damage to the battery may release dangerous chemicals, and could start a fire.

    • Do not pry under the top third of the battery, you may damage the volume button ribbon cable.

    Traduire

  7. iPhone 7 Rear Case Battery Removal: étape 6, image 1 de 1

    • Remove the battery from the rear case.

    • When installing the battery, refer to this guide to replace your battery's adhesive strips.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

Auteur

avec 3 autres contributeurs

Scott Havard

Membre depuis le 06/27/16

49 633 Réputation

31 tutoriels rédigés

Badges: 38

+ 35 badges supplémentaires

0 commentaires

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 1

Total : 488