Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Insert the large iPod opening tool into the seam between the front case and rear panel of the iPod, below the dock connector. Run the tool back and forth to create an opening. The tool's edge should point toward the rear panel to prevent any accidental scratching of the aluminum front case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Insert a small iPod opening tool into the seam on the Hold button side of the iPod, with the edge of the tool pointing toward the rear panel.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Gently enlarge the existing gap by pressing/wiggling the small iPod opening tool into the gap near each of the two tabs attached to the rear case, pushing the clips toward the center of the iPod until both have been freed.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Repeat the same procedure listed in the previous step to free the five clips along the headphone jack side of the iPod.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
After ensuring all tabs are free, separate the two halves of the iPod.
-
The rear panel is now free from the iPod.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the following 3 screws:
-
Two 3 mm Phillips screws near the dock connector.
-
One 4 mm Phillips screw along the edge of the logic board.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Peel up the ground strap connecting the battery to the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Insert the flat end of a spudger between the battery and the headphone jack side of the front case to pry the battery up off the adhesive securing it to the front case.
-
Rotate the battery out of the iPod and lay it next to the iPod. The battery is still soldered to the logic board by three wires, so don't remove it entirely.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Gently lift up on the dock connector end of the logic board to ensure the logic board is free.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Grasp the end of the logic board near the battery connector with one hand, and hold onto the rest of the iPod with your other hand.
-
Slide the logic board out of its holding brackets on the rear of the display.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger to flip up the black plastic tab holding the orange display ribbon in place. The black tab will rotate up 90 degrees, releasing the ribbon cable.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger to slide the display ribbon out of its connector.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger to flip up the black plastic tab holding the orange click wheel ribbon in place. The black tab will rotate up 90 degrees, releasing the ribbon cable.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger to slide the click wheel ribbon out of its connector.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
The logic board and battery are now free from the iPod.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger to carefully pry up the adhesive holding down the edge of the display.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Gently lift up on one corner of the display to separate the adhesive holding the display in place.
-
Lift up on the other corner of the display in the same manner.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift up on the click wheel cover and carefully thread the orange click wheel ribbon through the slot in the click wheel cover.
-
Lift the click wheel cover out of the iPod.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger to pry up the orange click wheel ribbon from the front panel.
-
Annulation : je n'ai pas terminé ce tutoriel.
13 autres ont terminé cette réparation.