Introduction

Est-ce que votre Nano a pris un choc ? Utilisez ce guide pour remplacer sa vitre incurvée.

Insérez le bord d'un outil d'ouverture pour iPod dans l'espace entre la coque extérieure et le cache supérieur.
  • Insérez le bord d'un outil d'ouverture pour iPod dans l'espace entre la coque extérieure et le cache supérieur.

  • Faites levier sur le cache supérieur pour le décoller de l'adhésif le fixant au dispositif de retenue de l'écran.

  • À ce stade, le bouton Arrêt n'est plus fixe et risque de tomber. Veillez à ne pas le perdre.

Be sure to use the smaller iPod opening tool and press it in FIRMLY in order to get enough leverage to get under the bezel and pry it off. Adhesive is very strong, so don't be afraid to use a little bit of force.

captcarl13 - Réponse

Retirez le bouton Arrêt du haut du Nano.
  • Retirez le bouton Arrêt du haut du Nano.

Ajouter un commentaire

  • Retirez les deux vis cruciformes coudées des deux coins du dispositif de retenue de l'écran.

  • Ces têtes de vis sont extrêmement petites et s'abîment facilement.

Be sure to use a good phillips #00 screwdriver here, or you run the risk of stripping the very small screws.

iTronics Repair - Réponse

The screws were covered with the adhesive. They were very difficult to remove.

I RUINED the hold switch! I accidentally broke the cord. 0_o The directions were kind of unclear.

bodieg - Réponse

Citation de bodieg :

The screws were covered with the adhesive. They were very difficult to remove.

I RUINED the hold switch! I accidentally broke the cord. 0_o The directions were kind of unclear.

Step 12 is misleading as it does not show to remove the screen from the metal frame.

bodieg - Réponse

Sorry guys, but the explanations are really bad. Go onto youtube and watch it. This site misses heaps of steps. I just broke my iPod :(

S Mile - Réponse

Like others have noted, screws are covered in adhesive and difficult to remove. Take extreme care to not strip the heads. I'd suggest using a very small flathead to scrape some of the adhesive off before attempting to remove the screws.

captcarl13 - Réponse

a 1mm slotted screwdriver will work in a pinch, but be carefull and make sure you get the angle just right

andrew - Réponse

The tools list doesn't say you need an iPod opener to, nor does the parts list day you'll need a new click wheel, though this is called ”...click wheel REPLACEMENT​”. I don't get the feeling these are very trustworthy instructions, ESPECIALLY after having read other comments. I'd say BEWARE, and look at a variety of resources to get a much more comprehensive picture.

Skyfire - Réponse

Actually, the screws are not aligned with the edges of the iPod, which means that you must not try to unscrew them vertically. If you do there is a good chance that you damage the head of the screws. Thus look carefully with a torch to see at what angle you have to unscrew them.

Fabrice Sarelli - Réponse

Actually, the screws are not aligned with the edges of the iPod. That means that if you try to unscrew them vertically, there is a good chance that you damage the head of the screws. Thus, look carefully with a torch to see exactly at what angle you need to unscrew them safelly.

Fabrice Sarelli - Réponse

Everything was good up to this point. I could barely see the screws and ended up stripping them. Just gave up at this point and threw the

Ipod on the ground and stomped on it.

gonzalo gonzalez - Réponse

I agree with several other contributors here, that a properly sized flat screwdriver *that is not worn* held at the correct angle is a better option than a phillips because the screw head is filled in with adhesive tape. BEWARE: The screws on the top and bottom outer edges are not parallel to the case. They are offset by 25 or 30 degrees, with the tips of the screws pointing out towards the outer edge of the case with respect to where the heads are. Use something to get magnification so you can really see how your screwdriver fits, and whether it’s engaged. An undamaged and properly sized standard screwdriver held in the appropriate orientation will readily remove the top and bottom side screws without stripping and with very little force. Feel for engagement — press the screwdriver in just enough to get past the adhesive. Not much torque or pressure is required — just a good fit. You must have the right tools to do this job successfully, and look under high magnification. Align your screwdriver!

Barry L. Kramer - Réponse

  • Insérez un outil d'ouverture pour iPod entre la coque extérieure et le dispositif de retenue de l'écran.

  • Utilisez l'outil pour faire légèrement légèrement l'écran de la coque.

  • Ne faites pas pivoter le dispositif de retenue de l'écran autour du bord supérieur de l'écran, car il est fixé à un support en acier mince qui se casse facilement.

  • Ne forcez pas le retrait du dispositif de retenue de l'écran, car la nappe du bouton Arrêt est susceptible de casser.

I found I had to gently pry the retainer open with a craft knife (xacto knife?) as the plastic opener tool was too blunt or soft to get any purchase...

aaaidan - Réponse

My nano had a "swollen" battery which wedged the LCD between battery and front glass. As a result, this step didn't work, I couldn't pull out the TFT and botched case, TFT and TFT frame until it came out. Telltale sign was a display that looked like there is a water between glass and LCD. The other nanos I've opened didnt have this problem and came out effortlessly, so if yours is stuck, don't feel bad, there's not much you can do!

oliver - Réponse

  • Faites glisser l'écran hors du Nano. Il se déplacera d'environ 1 cm jusqu'à ce que le câble de données de l'écran vous empêche de tirer plus.

  • Ne forcez pas sur le très mince câble de données de l'écran.

I have several problems in taking it out. I don't know if it is dued to the glue that the iPod has inside. Could you help me. Thanks

Hector - Réponse

instructions say 5" (inches) it really means 5mm

pedalsandpicks - Réponse

Citation de pedalsandpicks :

instructions say 5" (inches) it really means 5mm

If you're gonna repair the way you read it will get you nowhere: the text reads .(as point)5 inch. Which is about 12mm.

Frank veenis - Réponse

The glass panel can be very difficult to get moving requiring a lot of downward force. I have found good old fashioned spit to be very useful here.Just lick both thumbs and rub on fingers until just sticky enough.

This willl move the glass.

Pete Green - Réponse

  • Lorsque l'écran est sorti du boîtier autant que possible, appuyez doucement sur le bord inférieur de la vitre jusqu'à ce qu'elle se soulève légèrement (~ 1 mm).

  • Appuyez vos pouces sur le bord inférieur de la vitre pour la faire glisser vers le bas et dans le boîtier jusqu'à ce que le bord supérieur sorte du boîtier.

I found the adhesive (or fit) quite strong. Pushing on the bottom part of the glass created a small gap at the top, which I could fit a craft knife (xacto blade) into. This made it easier to carefully lever the glass out for me.

aaaidan - Réponse

I slipped and broke the LCD. So !#^&@@ off. What an absolute bastard of a job!

lf - Réponse

What is the "rear edge" of the nano? Can this be a bit clearer please? Maybe a video of this step would be a good idea. Then again, since Apple owns this site, I guess that's not gonna happen, is it?

lf - Réponse

I don't see "rear edge" anywhere in the instructions. I do see "lower edge" a few times and it looks pretty clear to me. I did this repair a couple years ago without much trouble.

Rene Jeddore -

You could do all these steps and really mess up your nano. Instead of disassembling the iPod, carefully remove the remnants of the old glass which I assumed you have cracked. With the new glass in hand CAREFULLY sand one edge of the glass evenly. I used my fine grinder on my dremel tool. After assuring a snug fit I removed the adhesive and installed the glass. Looks great and functional and I didn't ruin my iPod in the process. And when I said sand one edge I mean one of the edges that has a "lip" on it. The other lip you can slide right in and push gently down for a nice fit. Do not remove the adhesive until you are sure of a good fit. This is a quick fix for those who are too queezy to take apart their device.

Jim - Réponse

  • Soulevez la vitre du Nano.

  • Avant de réinstaller la vitre, assurez-vous de nettoyer la face de l'écran et l'intérieur de la vitre, car toute poussière ou empreinte digitale sera nettement visible lorsque le Nano est allumé.

Ajouter un commentaire

Conclusion

Pour réassembler votre appareil, suivez ces instructions dans l'ordre inverse.

28 autre(s) ont terminé cette réparation.

Merci à ces traducteurs :

100%

Ces traducteurs nous aident réparer le monde ! Vous voulez contribuer ?
Commencez à traduire ›

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 2

7 derniers jours : 28

30 derniers jours : 143

Total : 34,488