Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
-
Remplissez une casserole ou une poêle avec suffisamment d'eau pour immerger complètement un iOpener.
-
Faites chauffer l'eau jusqu'à ébullition. Puis éteignez le feu.
-
Placez un iOpener dans l'eau chaude pendant 2 à 3 minutes. Assurez-vous que l'iOpener est complètement immergé dans l'eau.
-
Utilisez des pinces pour extraire l'iOpener chauffé de l'eau chaude.
-
Séchez soigneusement l'iOpener avec une serviette.
-
Votre iOpener est prêt à être utilisé ! Si vous devez réchauffer l'iOpener, portez l'eau à ébullition, éteignez le feu et placez l'iOpener dans l'eau pendant 2 à 3 minutes.
-
-
-
Posez l'iOpener sur la languette en plastique pour desserrer l'adhésif. Laissez l'iOpener posé sur l'appareil pendant environ 90 secondes avant d'essayer d'ouvrir le panneau.
-
-
-
Utilisez un outil d'ouverture en plastique pour retirer de l'appareil le cache en plastique arrière jusqu'à ce qu'il y ait suffisamment d'espace pour y insérer un spudger.
-
Insérez un spudger sous le cache, puis tirez-le vers le haut et loin de l'appareil.
-
Retirez le cache en plastique arrière de l'iPod.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two 1.4 mm Phillips #000 screws from the sleep/power button bracket.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the sleep/power button bracket from the rear case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Insert a plastic opening tool under the sleep/power button, and gently pry upwards to free it from its adhesive.
-
Slide the plastic opening tool along the underside of the sleep/power button ribbon cable.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Peel back and remove any tape covering the volume control button assembly.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the three 1.4 mm Phillips #000 screws securing the volume control button assembly to the rear case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the pointed end of a spudger to pry the volume control button assembly away from the edge of the case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the single 2.8 mm Phillips #000 screw from the headphone jack.
-
Remove the 4 Phillips #000 screws from the lightning connector and logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use a spudger to pry the headphone jack off of the adhesive holding it to the rear case.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the flat end of a spudger to push the logic board away from the edges of the rear case to free the Lightning connector.
-
Once the Lightning connector has been loosened, push gently between it and the case to further free it.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Gently pull the logic board assembly out of the rear case.
-
Annulation : je n'ai pas terminé ce tutoriel.
19 autres ont terminé cette réparation.
12 commentaires
Fixing the headphone jack is super hard. I've been working on mine for a few months. And Basically I ordered the part on ebay (headphone jack, the power button is attached) and I pulled it apart, opened the ipod and swapped everything out (pay close attention to where pieces go cause there's no YouTube videos on how to do it yet) but there is a small piece attached to the ribbon cable near the headphone jack (it's square shaped, with looks like little grid thing, not sure the name) and it has to be perfectly lined up and contacts have to be touching for the power button, volume controls, an headphone jack to work. And that's where I'm stuck cause you can't use adhesive or it will block the contact points. So if you can find someone to replace your ipod parts it will be much easier.