Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
Cette étape n’est pas traduite. Aidez à la traduire
-
The picture at left (front panel already removed) shows the locations of the metal clips (shown in red) that snap on to the plastic frame. In the next few steps, try to pry the front panel up from the gaps between these clips.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Gently insert a plastic opening tool, near the volume control buttons, between the plastic surround of the screen and the metal case.
-
Rotate the tool away from the Touch to pry up on the glass panel.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Insert the plastic opening tool between the front panel and its plastic surround and pry up at several points along the left edge of the Touch.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Continue prying up the left edge until the top and bottom edges start to lift out of the Touch.
-
Once the top and bottom edges have lifted slightly out of the Touch, use the opening tool to assure the plastic surround is detached from the clips along the inside of the Touch.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Continue the prying procedure, now focusing on detaching the plastic surround from the internal metal clips.
-
Pry along the top edge of the Touch to further separate the front panel from the rest of the device.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pry up the front panel along the right edge using the method described in previous steps.
-
Eventually work around the entire perimeter of the front panel until it is lifted slightly from the rear panel.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the front panel out of the rear case minding the cable still attaching it near the upper left corner of the Touch.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the flat end of a spudger (or an opening tool) to pry the touch screen cable connector up off the upper logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Insert a small iPod opening tool with the edge angled up toward the underside of the display between the white plastic backlight and the metal shield beneath it.
-
Pry up along the lower edge of the display enough to grab it with your fingers.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the display up from its lower edge and rotate it toward the top of the Touch.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
While holding the display with one hand, run an iPod opening tool down the two long edges of the mylar reflector attached to the metal display tray.
-
When it is sufficiently free from the display tray, remove the mylar reflector from the Touch.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the seven Phillips screws securing the metal display tray to the rear panel.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lay the display back down into its tray.
-
Remove the final Phillips screw securing the metal tray to the rear panel.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the display out of the metal tray and rotate it toward the top edge of the Touch.
-
Use an iPod opening tool to lift the metal display tray and rotate it up toward the top edge of the Touch.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use the edge of an iPod opening tool to peel the copper tape off the top edge of the display.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Use an iPod opening tool to pry the display cable connector up off its socket on the logic board.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Lift the metal display tray slightly (the battery is attached to its underside) and remove the display from the Touch, minding its delicate cable that may get caught.
-
Annulation : je n'ai pas terminé ce tutoriel.
168 autres ont terminé cette réparation.
4 commentaires
Somehow it always get left out of these tutorals that the !@#$ thing has ALL parts glued together! There's a thin layer of what looks like silicon sealant/glue between the glass and the metal shell. Then the LCD is glued (also with silicon) to mylar backing and mylar backing is glued to the metal frame. The battery is also glued to that frame. The glue gives if you're persistent but it's very easy to crack the LCD while trying to pry it from the metal frame and I had to literally cut the battery off of the other side of that frame.
Having successfully changed several iPhone batteries I decided to replace the cracked glass on my 2nd Gen Touch but it's practically impossible to do without damaging the rest of the iPod. With 2nd hand values as they are now in 2022 it's actually cheaper to buy a decent second hand 3rd. Gen one than it cost to buy the new screen, mid-frame & glue to repair the original.!! Not my ideal as I wanted to repair the old one, but at least I'm making use of another iPod that the previous owner no longer wanted. I have no doubt that these are repairable but a great deal of care & experience / practice is required & mine ended up being scrapped :-(