Aller au contenu principal

iPhone 12 Pro Max 电池更换

Anglais
Chinois

Conditions préalables au tutoriel

Tous les tutoriels prérequis doivent être traduits avant que cette traduction soit considérée comme complète.

iPhone 12 Pro Max 五角螺丝更换

三角撬片深度标记

iPhone 12 Pro Max 显示屏总成更换

iPhone 12 Pro Max 扬声器更换

iPhone 12 Pro Taptic Engine 更换

Informations sur le tutoriel

= Terminé = Incomplet
    iPhone batteries are rated to hold 80% of their capacity for up to 500 charge cycles, which lasts roughly 18-24 months for most users. After that, your iPhone may need to be charged far more frequently, and iOS may warn you that performance is affected (in other words, your phone will run slower). Use this guide to replace your battery and restore your iPhone to like-new performance.
    If your battery is swollen, [[What to do with a swollen battery|take appropriate precautions|new_window=true]].
    ***Note***: After the repairOn iOS 17.6 and earlier, your iPhone may display a warning about the “genuineness” of the battery after the repair, even when using original Apple parts. If your iPhone functions normally, you can safely ignore the warning. On iOS 18 and newer, authenticate your new battery using Apple's [link|https://support.apple.com/en-us/120579|Repair Assistant|new_window=true].
    For optimal performance, after completing this guide, [[Battery Calibration|calibrate]] your newly installed battery: Charge it to 100% and keep charging it for at least two more hours. Then use your iPhone until it shuts off due to low battery. Finally, charge it uninterrupted to 100%.
      Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.
      ***To reassemble your device, follow the above steps in reverse order.***
      After your repair, depending on the replacement part, you may be able to [link|https://support.apple.com/en-us/120579|calibrate it using Apple's Repair Assistant|new_window=true], available as of iOS 18. Update your device, navigate to Settings ***→*** General ***→***About ***→*** Parts & Service History, tap Restart & Finish Repair, and follow the onscreen prompts.
      Take your e-waste to an [[E-Waste|R2 or e-Stewards certified recycler|new_window=true]].
      Repair didn’t go as planned? Try some [[Troubleshooting Problems After a Repair|basic troubleshooting]], or ask our [link|https://www.ifixit.com/Answers/Device/iPhone%2012%20Pro%20Max|iPhone 12 Pro Max Answers community] for help.

      Étapes du tutoriel

      Étape 1 — 找到粘合剂小拉条

      电池用四块可拉伸释放的粘合剂固定在后壳上,两块在电池的底部边缘,两块在顶部边缘。

      Étape 2 — 去除拉伸释放胶

      剥下第一个电池粘合剂拉条,使其脱离电池底部边缘。

      Étape 3

      剥下第二个电池粘合剂拉条,以使其脱离电池底部边缘。

      Étape 4

      用手指抓住第一个拉环,然后将其从电池中缓慢拉出,朝 iPhone 的底部移动。

      Étape 5

      用手指抓住第二个拉环,将其从电池中拉出,朝iPhone的底部移动。

      Étape 6

      剥下剩余的两个电池粘合小拉条,以使其脱离电池顶部边缘。

      Étape 7

      使用与之前相同的步骤,一次拉出其余两个小拉条,以拉伸并取下将电池固定到位的剩余胶带。尽量不要将粘合剂粘在任何东西上。

      Étape 8 — 如何取出卡住的电池

      如果仍然无法卸下电池,请在破裂的胶条区域内的电池边缘下方滴几滴高浓度(超过90%)的异丙醇。

      Étape 9 — 移除电池

      取出电池。

      Vos contributions sont faites dans le cadre de la licence open source Creative Commons.