Réparez vos affaires Communauté Boutique

Logitech M510 Teardown

Rédigé par : Xavier (et 2 autres contributeurs)
Publication : April 21, 2021
  • Commentaires : 5
  • Favoris : 0
  • Vues : 8,3k

Logitech M510 Teardown

Rédigé par : Xavier (et 2 autres contributeurs)
Publication : April 21, 2021
  • Commentaires : 5
  • Favoris : 0
  • Vues : 8,3k

Vue éclatée

Introduction

Today we are going to be taking apart the Logitech M510 mouse.

Ce dont vous avez besoin

Vidéo d'introduction

Cette vue éclatée n'est pas un tutoriel de réparation. Pour réparer votre Logitech M510, utilisez notre manuel de réparation.

  1. Logitech M510 Teardown, Logitech M510 Teardown: étape 1, image 1 de 1

    • Let's get started!

    Modifier

  2. Logitech M510 Teardown: étape 2, image 1 de 1

    • Flip your mouse over

    Modifier

  3. Logitech M510 Teardown: étape 3, image 1 de 1

    • Remove the batteries by pulling on the tab.

    • If you do not plan on putting it back together, ensure you dispose of the batteries properly.

    Modifier

  4. Logitech M510 Teardown: étape 4, image 1 de 1

    • Take the battery pull tab that is circled in red and tape it to the area that is circled in blue

    • This allows you to access the screws that are hidden by the battery pull tab

    Modifier

  5. Logitech M510 Teardown: étape 5, image 1 de 1

    • Unscrew the two screws that are circled in yellow.

    Modifier

  6. Logitech M510 Teardown: étape 6, image 1 de 1

    • Remove the tape

    Modifier

  8. Logitech M510 Teardown: étape 7, image 1 de 1

    • Now you can easily separate the bottom and the top of the device.(Just give it a little tug)

    Modifier

  9. Logitech M510 Teardown: étape 8, image 1 de 1

    • Okay now that we've got it separated we can have a sneak peek inside

    • The scroll wheel.

    • The battery area

    • Mouse buttons

    Modifier

  10. Logitech M510 Teardown: étape 9, image 1 de 1

    • Now unscrew the screw that is circled in yellow

    Modifier

  11. Logitech M510 Teardown: étape 10, image 1 de 1

    • Now disconnect the cable there is circled in blue by unplugging it from the logic board.

    Modifier

  12. Logitech M510 Teardown: étape 11, image 1 de 1

    • We have taken apart the bottom half, So let's take apart the top half.

    • This is the on-off switch.

    Modifier

  13. Logitech M510 Teardown: étape 12, image 1 de 1

    • Let's get started disassembling the top half

    • Remove the two screws circled in yellow.

    Modifier

  14. Logitech M510 Teardown: étape 13, image 1 de 1

    • Okay now that we've got that done, lets continue

    Modifier

  15. Logitech M510 Teardown: étape 14, image 1 de 1

    • Remove the screw circled in yellow

    Modifier

  16. Logitech M510 Teardown: étape 15, image 1 de 1

    • Now you can pop out the scroll buttons.

    Modifier

  17. Logitech M510 Teardown: étape 16, image 1 de 1

    • Now pop out the piece circled in yellow

    Modifier

  18. Logitech M510 Teardown: étape 17, image 1 de 1

    • And there we go we have disassembled the entire mouse.

    Modifier

Auteur

avec 2 autres contributeurs

Xavier

Membre depuis le 04/20/21

352 Réputation

1 tutoriel rédigé

Badges: 9

+ 6 badges supplémentaires

Équipe

X71FS Membre de l'équipe X71FS

Community

1 membre

3 tutoriels rédigés

5 commentaires

I’ve actually seen a model of this same mouse where optics sensor is MODULAR with a ribbon cable. So much better for repairability!

Giorgi - Réponse

I don’t have this mouse, but an LX8 Cordless Laser Mouse. It looked quite similar so gave it a go, and presto! It opened up easily, I could get to all the internal bits quite easily and removed years of cat hair, tobacco grains and human oils which had formed felt mats around the moving parts and gummed it up completely! Now factory fresh and restored to full function - couldn’t be happier! Thanks Xavier!

Adrian Mann - Réponse

It says the video is private.

Michael Norton - Réponse

The video is private. But the instructions are good without the video.

Note that the front-side of the mouse has tabs that hold the pieces together, so mate the front of the mouse (the button-side) before mating the end closes to the batteries (and the screws)

Adam Goldberg - Réponse

Thanks! It would be great if you showed how to take the wheel out - it has to be pried out of its seat in the front of the mouse. FYI for cleaning it only takes steps 1 thru 8 plus taking out the wheel.

PB - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 24

7 derniers jours : 101

30 derniers jours : 341

Total : 8,300