Réparez vos affaires

Droit à la réparation

Boutique

Motorola Moto G3 Teardown

Rédigé par : Witrigs (et 3 autres contributeurs)
  • Commentaires : 9
  • Favoris : 22
  • Réparations terminées : 15

Difficulté

Modérée

Étapes

16

Temps nécessaire

25 minutes

Sections

1

Drapeaux

1

Member-Contributed Guide

Un membre a contribué à ce tutoriel

Un membre tout à fait remarquable de notre communauté a réalisé ce tutoriel. Il n'a pas été dirigé par l'équipe iFixit.

Vidéo d'introduction

  1. Remove back cover. Moto G3 plastic panel can be easily removed with the fingernails.

    • Remove back cover.

    • Moto G3 plastic panel can be easily removed with the fingernails.

    Traduire

  2. Remove camera&flashlight metal cover. Use tweezers to cut strong adhesives underneath. Remove camera&flashlight metal cover. Use tweezers to cut strong adhesives underneath.

    • Remove camera&flashlight metal cover. Use tweezers to cut strong adhesives underneath.

    Traduire

  3. Undo 3 screws by T4 Torx screwdriver. Take away plastic securing part.

    • Undo 3 screws by T4 Torx screwdriver.

    • Take away plastic securing part.

    Traduire

  4. Heat up the LCD screen for a while. Then with the help of suction cup, insert guitar picks to open a gap. Slide guitar picks or plastic opening tool to cut strong adhesives. There is LCD screen connector on the left side, so be careful to slide guitar picks.

    • Heat up the LCD screen for a while.

    • Then with the help of suction cup, insert guitar picks to open a gap. Slide guitar picks or plastic opening tool to cut strong adhesives.

    • There is LCD screen connector on the left side, so be careful to slide guitar picks.

    Traduire

  5. Release LCD screen connector firstly. Remove LCD screen. Remove LCD screen.

    • Release LCD screen connector firstly.

    • Remove LCD screen.

    Traduire

  6. Undo 14 screws by T4 Torx screwdriver Pry up motherboard assembly. Battery flex connector is connected with motherboard, so be careful to pry the assembly up.

    • Undo 14 screws by T4 Torx screwdriver

    • Pry up motherboard assembly.

    • Battery flex connector is connected with motherboard, so be careful to pry the assembly up.

    Traduire

  8. Release battery flex connector. Separate motherboard assembly from back cover assembly.

    • Release battery flex connector.

    • Separate motherboard assembly from back cover assembly.

    Traduire

  9. Undo 3 screws here. Use spudger to cut adhesives and pry the SIM&SD card reader board, then remove it. Use spudger to cut adhesives and pry the SIM&SD card reader board, then remove it.

    • Undo 3 screws here.

    • Use spudger to cut adhesives and pry the SIM&SD card reader board, then remove it.

    Traduire

  10. Remove front-facing camera. Remove front-facing camera.

    • Remove front-facing camera.

    Traduire

  11. Remove rear camera. Remove rear camera. Remove rear camera.

    • Remove rear camera.

    Traduire

  12. Remove earpiece. Remove earpiece.

    • Remove earpiece.

    Traduire

  13. Remove loudspeaker. Remove loudspeaker.

    • Remove loudspeaker.

    Traduire

  14. Here is the motherboard. Here is the motherboard.

    • Here is the motherboard.

    Traduire

  15. Use spudger to cut adhesive and pry the battery up. Use spudger to cut adhesive and pry the battery up.

    • Use spudger to cut adhesive and pry the battery up.

    Traduire

  16. Take away headphone jack. Take away headphone jack. Take away headphone jack.

    • Take away headphone jack.

    Traduire

  17. Done

    • Done

    Traduire
Ligne d'arrivée

15 autre(s) ont terminé cette réparation.

Auteur

avec 3 autres contributeurs

Witrigs

Membre depuis le 24/11/2015

65 815 Réputation

386 tutoriels rédigés

Badges: 32

+ 29 badges supplémentaires

7 commentaires

Ajouter un commentaire

Muito bom, parabéns!

Manoel - Réponse

Could you guys tell me if the main speaker, at the bottom, has a special protection agains water spills, like a membrane or so, or is it pretty fine too spill water there?

setsuoleandro - Réponse

Wi fi not trun on ..moto g3

Seoni Seoni - Réponse

When you heat up the display, do you heat up the entire display or just around the edges? What heat gun/setting should i use? Can i use a blowdryer?

guest - Réponse

Thanks. ......................

Biswajit Saha - Réponse

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 4

7 derniers jours : 19

30 derniers jours : 128

Total : 21,134