Outils recommandés dans ce démontage

Introduction

This guide shows you how to completely disassemble your camera.

Cette vue éclatée n'est pas un tutoriel de réparation. Pour réparer votre Polaroid One-Step 600, utilisez notre manuel de réparation.

Open the flash/lens compartment of the Polaroid camera to a 30 degree angle with the horizontal.
  • Open the flash/lens compartment of the Polaroid camera to a 30 degree angle with the horizontal.

Ajouter un commentaire

Separate the flash section of the camera from the main body by unhooking the sides.
  • Separate the flash section of the camera from the main body by unhooking the sides.

  • BE CAREFUL NOT TO YANK THE TWO SECTIONS APART BECAUSE THE BAND WIRE STILL ATTACHES THEM!

Ajouter un commentaire

  • Open the battery/ cartridge compartment fully.

Ajouter un commentaire

  • Insert spudger in between face of camera and sides where the four tabs are located.

Ajouter un commentaire

  • Once tabs are released, pull face of camera straight out.

Ajouter un commentaire

  • Remove the capture button if it did not pop out when you removed the face.

  • There are two pieces to the capture button and both should be removed.

Ajouter un commentaire

  • To remove the back of the camera, you have to find the tabs located near the hinges of the battery and film compartment.

  • Using a screw driver, pry the tabs of the outer case away from the metal frame.

  • Once the tabs are removed slide the metal frame forward.

Ajouter un commentaire

  • Remove the battery and film compartment latch

  • Pull the metal frame away from the case.

  • The entire case will come off but the flash compartment will come with the insides of the camera.

Ajouter un commentaire

  • Using a spudger, pop the battery and film cartridge hatch from its hinges.

  • The tabs are located at the bottom of the metal frame.

Ajouter un commentaire

  • Remove the sight by lifting it straight up.

  • Follow the red wire from the flash compartment

  • Take the red wire off of the 2 hooks

  • Slide the uncovered wire end out of the small brass clip. Move wire away from camera.

Ajouter un commentaire

  • Follow the black wire from flash bulb to the back of the case.

  • When you find the brass tab, pull it up. When the tab is free, remove the tab from the black wire.

Ajouter un commentaire

  • Follow the metal band from the flash compartment to the brass tab.

  • Unhook the wire on the left of the brass tab.

  • Remove the metal band from behind the brass clip.

  • Set the now detached flash compartment to the side.

  • Pull the brass tab up and out like the first one and remove the uncovered wire.

Ajouter un commentaire

  • Slide the brightness adjuster to right and off the camera.

  • Use the pointed end of the spudger to lift a small latch located next to the bottom of lenz plate

  • Then find the small latch located below the plastic bridge that is over the shutter mechanism

  • This latch is small and is hard to see but you just have to push it with the pointed end of the spudger to unlatch it.

Ajouter un commentaire

  • Using the pointed end of the spudger, pull the band wire out of the electric motor.

  • In the same manner as above, remove the band wire from the plastic extension.

Ajouter un commentaire

  • Rotate the lens plate up to unhook the plat from two tabs located at the top of the plate.

  • Remove the lens plate, flash compartment and wires from the camera.

Ajouter un commentaire

  • Follow the uncovered wire around the side of the camera

  • Remove the metal spring tab next to the counter

  • Remove the brass tab by lifting the top piece over the notch and sliding back.

Ajouter un commentaire

  • Locate the small brass tab with the uncovered wire running through it.

  • Remove the wire by sliding under the hooks.

  • then unhook the uncovered wire from the the final latch located on the top of the plastic extension.

Ajouter un commentaire

  • The cameras insides could now be in two major pieces.

  • The Pyramid and the lens plate

Ajouter un commentaire

  • The top of the pyramid has cover that can be lifted off

  • Below is the mirror which is held in by a tab.

  • Lift the tab with the spudger and pop out the mirror.

  • If you intend to reassemble the camera make sure the mirror is completely clean without any spots or fingerprints because they will affect the quality of your pictures.

Ajouter un commentaire

  • There are 4 tabs total that must be removed for the next step

  • The first is directly under the spring mounted at the back left of the camera

  • The next is located on the front of the plastic extension

  • The third tab is used to connect the metal frame to the outer plastic

Ajouter un commentaire

  • The final tab holds several spring loaded pieces together, these may pop out the moment the tab is released.

  • The final tab is located below the backside of the photo-counter dial.

  • The numbers will be right side up if you are looking in the right direction.

  • Once all four tabs are removed the plate pulls out from the slot in the rear.

Ajouter un commentaire

  • Lift the large gear away from its pin

  • The next piece is loaded with a small spring.

  • Carefully lift the "Y" shaped plastic piece from its pin and pull the spring from the pin as it is removed.

Ajouter un commentaire

  • Remove the Spring attached to the photo-counter dial.

  • Lift the photo-counter Dial off of its pin.

Ajouter un commentaire

  • Remove the spring attached to the film eject metal slide.

  • Remove the film eject metal slide

Ajouter un commentaire

  • Remove the plastic extension by pulling it from the slot in the rear of the camera.

Ajouter un commentaire

  • Remove the metal gear from the gear set.

  • Pull the "L" shaped black plastic piece off of its pin.

Ajouter un commentaire

  • There are four gears to remove.

  • The gear on the left goes first, followed by the the right.

  • The right gear has a small leaf spring between it and the gear below it.

  • Then remove the black gear and then the last white gear.

Ajouter un commentaire

  • Using the pointed end of the spudger, press the clip that is beneath all the gears next to the electric motor gear.

  • Lift the plastic box containing several long metal tabs

  • Then slide the box out.

Ajouter un commentaire

  • Pull the electric motor straight out of the plastic piece.

Ajouter un commentaire

  • Remove the spring located in the middle of the plastic mechanism.

  • Remove the two loose plastic pieces.

Ajouter un commentaire

  • To remove the metal frame, press the two tabs with the spudger and slide it forward.

Ajouter un commentaire

  • With the point of the spudger, remove the band wire from the solenoid.

  • Remove the small LED from its clip, and then lift the flat wire array and the flash compartment away from the back of the lens plate.

Ajouter un commentaire

  • Remove the solenoid from the back of the lens plate by removing the two tabs.

Ajouter un commentaire

  • Remove the lens by pressing the tab.

  • CAUTION: The lens may pop out when the tab is released.

  • Remove the back of the lens plate by unhooking the three clips that hold it together.

  • CAUTION: The Shutter leaves may fall out during this step.

Ajouter un commentaire

  • Remove the spring on the plastic bridge that attaches to the shutter mechanism

  • Remove the Shutter mechanism from the back of the lens plate.

Ajouter un commentaire

  • Remove the Clear dial by unhooking the tab at the bottom of the dial

  • Lift the light blue piece out of the mechanism.

  • Lift the black piece out of the plastic plate.

Ajouter un commentaire

  • Remove the clear green prism from the plastic plate.

Ajouter un commentaire

  • The disassembled camera.

how do you remove the neck strap and replace it with a strap that is 3/8" wide web? And if you could, please include photographs.

Thank you!

Kourtney - Réponse

Adriano Agostino

Membre depuis le 22/01/2010

27 Réputation

1 tutoriel rédigé

Équipe

Cal Poly, Team 16-31, Maness Winter 2010 Membre de l'équipe Cal Poly, Team 16-31, Maness Winter 2010

CPSU-MANESS-W10S16G31

4 membres

4 tutoriels rédigés

Is it possible to remove and change the camera straps for this camera?

stylencreate - Réponse

Yes, after step 8 you will have the back case free then in the inside you will see the latches of the plastic plate that holds the strap, pry them carefully are 6, 2 on each side and 2 in the middle, in the middle of doing it myself have stopped since was no need for that so cannot tell you more.

eportillo5000 - Réponse

Show me how to teardown the flash plz

RAW Fish - Réponse

RAW Fish: Get a terminal driver or other thin device, and wedge it where you can see a line between the outer casing and front panel (where it says “Polaroid” with the rainbow logo). This will need a bit of brute force, but you will be able to seperate a right-angle of outer casing, from the back of the flash, and another right angled bit full of electrics and the front panel. DO NOT touch any of this electrical gubbins - discharging the capacitor through your fingers will HURT. From here you can take out the circuit board and do with it what you wish.

Ariane N -

Hi ! Thanks for your article ! I just bought a Barbie polaroid 600 ;) but unfortunately the flat wire between the camera the flash is disconnected (it dangles from the camera). I managed to remove the flash, that is no longer connected. Do you know how can I open the flash part to reconnect the wires ? Thanks ;)

Marie Dodue - Réponse

Is it possible to reassembly the camera after the teardown?

CameraObscura - Réponse

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 7

7 derniers jours : 71

30 derniers jours : 398

Total : 33,955