Aller au contenu principal

Ce dont vous avez besoin

Cette vue éclatée n'est pas un tutoriel de réparation. Pour réparer votre Polaroid One-Step 600, utilisez notre manuel de réparation.

  1. Polaroid One-Step 600 Teardown, Polaroid One-Step 600 Teardown: étape 1, image 1 de 3 Polaroid One-Step 600 Teardown, Polaroid One-Step 600 Teardown: étape 1, image 2 de 3 Polaroid One-Step 600 Teardown, Polaroid One-Step 600 Teardown: étape 1, image 3 de 3
    • Open the flash/lens compartment of the Polaroid camera to a 30 degree angle with the horizontal.

  2. Polaroid One-Step 600 Teardown: étape 2, image 1 de 3 Polaroid One-Step 600 Teardown: étape 2, image 2 de 3 Polaroid One-Step 600 Teardown: étape 2, image 3 de 3
    • Separate the flash section of the camera from the main body by unhooking the sides.

    • BE CAREFUL NOT TO YANK THE TWO SECTIONS APART BECAUSE THE BAND WIRE STILL ATTACHES THEM!

  3. Polaroid One-Step 600 Teardown: étape 3, image 1 de 1
    • Open the battery/ cartridge compartment fully.

    My film door latch came off the camera and I can’t get the film door open ? Help.

    Armando Barajas - Réponse

  4. Polaroid One-Step 600 Teardown: étape 4, image 1 de 3 Polaroid One-Step 600 Teardown: étape 4, image 2 de 3 Polaroid One-Step 600 Teardown: étape 4, image 3 de 3
    • Insert spudger in between face of camera and sides where the four tabs are located.

  5. Polaroid One-Step 600 Teardown: étape 5, image 1 de 2 Polaroid One-Step 600 Teardown: étape 5, image 2 de 2
    • Once tabs are released, pull face of camera straight out.

  6. Polaroid One-Step 600 Teardown: étape 6, image 1 de 2 Polaroid One-Step 600 Teardown: étape 6, image 2 de 2
    • Remove the capture button if it did not pop out when you removed the face.

    • There are two pieces to the capture button and both should be removed.

  7. Polaroid One-Step 600 Teardown: étape 7, image 1 de 3 Polaroid One-Step 600 Teardown: étape 7, image 2 de 3 Polaroid One-Step 600 Teardown: étape 7, image 3 de 3
    • To remove the back of the camera, you have to find the tabs located near the hinges of the battery and film compartment.

    • Using a screw driver, pry the tabs of the outer case away from the metal frame.

    • Once the tabs are removed slide the metal frame forward.

    How to force it?Is it up and down or left and right?

    王霸胆 - Réponse

  8. Polaroid One-Step 600 Teardown: étape 8, image 1 de 2 Polaroid One-Step 600 Teardown: étape 8, image 2 de 2
    • Remove the battery and film compartment latch

    • Pull the metal frame away from the case.

    • The entire case will come off but the flash compartment will come with the insides of the camera.

  9. Polaroid One-Step 600 Teardown: étape 9, image 1 de 1
    • Using a spudger, pop the battery and film cartridge hatch from its hinges.

    • The tabs are located at the bottom of the metal frame.

  10. Polaroid One-Step 600 Teardown: étape 10, image 1 de 3 Polaroid One-Step 600 Teardown: étape 10, image 2 de 3 Polaroid One-Step 600 Teardown: étape 10, image 3 de 3
    • Remove the sight by lifting it straight up.

    • Follow the red wire from the flash compartment

    • Take the red wire off of the 2 hooks

    • Slide the uncovered wire end out of the small brass clip. Move wire away from camera.

  11. Polaroid One-Step 600 Teardown: étape 11, image 1 de 3 Polaroid One-Step 600 Teardown: étape 11, image 2 de 3 Polaroid One-Step 600 Teardown: étape 11, image 3 de 3
    • Follow the black wire from flash bulb to the back of the case.

    • When you find the brass tab, pull it up. When the tab is free, remove the tab from the black wire.

  12. Polaroid One-Step 600 Teardown: étape 12, image 1 de 3 Polaroid One-Step 600 Teardown: étape 12, image 2 de 3 Polaroid One-Step 600 Teardown: étape 12, image 3 de 3
    • Follow the metal band from the flash compartment to the brass tab.

    • Unhook the wire on the left of the brass tab.

    • Remove the metal band from behind the brass clip.

    • Set the now detached flash compartment to the side.

    • Pull the brass tab up and out like the first one and remove the uncovered wire.

  13. Polaroid One-Step 600 Teardown: étape 13, image 1 de 3 Polaroid One-Step 600 Teardown: étape 13, image 2 de 3 Polaroid One-Step 600 Teardown: étape 13, image 3 de 3
    • Slide the brightness adjuster to right and off the camera.

    • Use the pointed end of the spudger to lift a small latch located next to the bottom of lenz plate

    • Then find the small latch located below the plastic bridge that is over the shutter mechanism

    • This latch is small and is hard to see but you just have to push it with the pointed end of the spudger to unlatch it.

  14. Polaroid One-Step 600 Teardown: étape 14, image 1 de 2 Polaroid One-Step 600 Teardown: étape 14, image 2 de 2
    • Using the pointed end of the spudger, pull the band wire out of the electric motor.

    • In the same manner as above, remove the band wire from the plastic extension.

  15. Polaroid One-Step 600 Teardown: étape 15, image 1 de 2 Polaroid One-Step 600 Teardown: étape 15, image 2 de 2
    • Rotate the lens plate up to unhook the plat from two tabs located at the top of the plate.

    • Remove the lens plate, flash compartment and wires from the camera.

  16. Polaroid One-Step 600 Teardown: étape 16, image 1 de 3 Polaroid One-Step 600 Teardown: étape 16, image 2 de 3 Polaroid One-Step 600 Teardown: étape 16, image 3 de 3
    • Follow the uncovered wire around the side of the camera

    • Remove the metal spring tab next to the counter

    • Remove the brass tab by lifting the top piece over the notch and sliding back.

  17. Polaroid One-Step 600 Teardown: étape 17, image 1 de 3 Polaroid One-Step 600 Teardown: étape 17, image 2 de 3 Polaroid One-Step 600 Teardown: étape 17, image 3 de 3
    • Locate the small brass tab with the uncovered wire running through it.

    • Remove the wire by sliding under the hooks.

    • then unhook the uncovered wire from the the final latch located on the top of the plastic extension.

  18. Polaroid One-Step 600 Teardown: étape 18, image 1 de 2 Polaroid One-Step 600 Teardown: étape 18, image 2 de 2
    • The cameras insides could now be in two major pieces.

    • The Pyramid and the lens plate

  19. Polaroid One-Step 600 Teardown: étape 19, image 1 de 3 Polaroid One-Step 600 Teardown: étape 19, image 2 de 3 Polaroid One-Step 600 Teardown: étape 19, image 3 de 3
    • The top of the pyramid has cover that can be lifted off

    • Below is the mirror which is held in by a tab.

    • Lift the tab with the spudger and pop out the mirror.

    • If you intend to reassemble the camera make sure the mirror is completely clean without any spots or fingerprints because they will affect the quality of your pictures.

  20. Polaroid One-Step 600 Teardown: étape 20, image 1 de 3 Polaroid One-Step 600 Teardown: étape 20, image 2 de 3 Polaroid One-Step 600 Teardown: étape 20, image 3 de 3
    • There are 4 tabs total that must be removed for the next step

    • The first is directly under the spring mounted at the back left of the camera

    • The next is located on the front of the plastic extension

    • The third tab is used to connect the metal frame to the outer plastic

  21. Polaroid One-Step 600 Teardown: étape 21, image 1 de 2 Polaroid One-Step 600 Teardown: étape 21, image 2 de 2
    • The final tab holds several spring loaded pieces together, these may pop out the moment the tab is released.

    • The final tab is located below the backside of the photo-counter dial.

    • The numbers will be right side up if you are looking in the right direction.

    • Once all four tabs are removed the plate pulls out from the slot in the rear.

  22. Polaroid One-Step 600 Teardown: étape 22, image 1 de 3 Polaroid One-Step 600 Teardown: étape 22, image 2 de 3 Polaroid One-Step 600 Teardown: étape 22, image 3 de 3
    • Lift the large gear away from its pin

    • The next piece is loaded with a small spring.

    • Carefully lift the "Y" shaped plastic piece from its pin and pull the spring from the pin as it is removed.

  23. Polaroid One-Step 600 Teardown: étape 23, image 1 de 2 Polaroid One-Step 600 Teardown: étape 23, image 2 de 2
    • Remove the Spring attached to the photo-counter dial.

    • Lift the photo-counter Dial off of its pin.

  24. Polaroid One-Step 600 Teardown: étape 24, image 1 de 2 Polaroid One-Step 600 Teardown: étape 24, image 2 de 2
    • Remove the spring attached to the film eject metal slide.

    • Remove the film eject metal slide

  25. Polaroid One-Step 600 Teardown: étape 25, image 1 de 1
    • Remove the plastic extension by pulling it from the slot in the rear of the camera.

  26. Polaroid One-Step 600 Teardown: étape 26, image 1 de 2 Polaroid One-Step 600 Teardown: étape 26, image 2 de 2
    • Remove the metal gear from the gear set.

    • Pull the "L" shaped black plastic piece off of its pin.

  27. Polaroid One-Step 600 Teardown: étape 27, image 1 de 2 Polaroid One-Step 600 Teardown: étape 27, image 2 de 2
    • There are four gears to remove.

    • The gear on the left goes first, followed by the the right.

    • The right gear has a small leaf spring between it and the gear below it.

    • Then remove the black gear and then the last white gear.

  28. Polaroid One-Step 600 Teardown: étape 28, image 1 de 3 Polaroid One-Step 600 Teardown: étape 28, image 2 de 3 Polaroid One-Step 600 Teardown: étape 28, image 3 de 3
    • Using the pointed end of the spudger, press the clip that is beneath all the gears next to the electric motor gear.

    • Lift the plastic box containing several long metal tabs

    • Then slide the box out.

  29. Polaroid One-Step 600 Teardown: étape 29, image 1 de 1
    • Pull the electric motor straight out of the plastic piece.

  30. Polaroid One-Step 600 Teardown: étape 30, image 1 de 3 Polaroid One-Step 600 Teardown: étape 30, image 2 de 3 Polaroid One-Step 600 Teardown: étape 30, image 3 de 3
    • Remove the spring located in the middle of the plastic mechanism.

    • Remove the two loose plastic pieces.

  31. Polaroid One-Step 600 Teardown: étape 31, image 1 de 1
    • To remove the metal frame, press the two tabs with the spudger and slide it forward.

  32. Polaroid One-Step 600 Teardown: étape 32, image 1 de 2 Polaroid One-Step 600 Teardown: étape 32, image 2 de 2
    • With the point of the spudger, remove the band wire from the solenoid.

    • Remove the small LED from its clip, and then lift the flat wire array and the flash compartment away from the back of the lens plate.

  33. Polaroid One-Step 600 Teardown: étape 33, image 1 de 1
    • Remove the solenoid from the back of the lens plate by removing the two tabs.

  34. Polaroid One-Step 600 Teardown: étape 34, image 1 de 2 Polaroid One-Step 600 Teardown: étape 34, image 2 de 2
    • Remove the lens by pressing the tab.

    • CAUTION: The lens may pop out when the tab is released.

    • Remove the back of the lens plate by unhooking the three clips that hold it together.

    • CAUTION: The Shutter leaves may fall out during this step.

  35. Polaroid One-Step 600 Teardown: étape 35, image 1 de 2 Polaroid One-Step 600 Teardown: étape 35, image 2 de 2
    • Remove the spring on the plastic bridge that attaches to the shutter mechanism

    • Remove the Shutter mechanism from the back of the lens plate.

  36. Polaroid One-Step 600 Teardown: étape 36, image 1 de 3 Polaroid One-Step 600 Teardown: étape 36, image 2 de 3 Polaroid One-Step 600 Teardown: étape 36, image 3 de 3
    • Remove the Clear dial by unhooking the tab at the bottom of the dial

    • Lift the light blue piece out of the mechanism.

    • Lift the black piece out of the plastic plate.

  37. Polaroid One-Step 600 Teardown: étape 37, image 1 de 1
    • Remove the clear green prism from the plastic plate.

  38. Polaroid One-Step 600 Teardown: étape 38, image 1 de 1
    • The disassembled camera.

    how do you remove the neck strap and replace it with a strap that is 3/8" wide web? And if you could, please include photographs.

    Thank you!

    Kourtney - Réponse

Adriano Agostino

Membre depuis le 01/22/10

50 Réputation

1 tutoriel rédigé

Équipe

Cal Poly, Team 16-31, Maness Winter 2010 Membre de l'équipe Cal Poly, Team 16-31, Maness Winter 2010

CPSU-MANESS-W10S16G31

4 membres

6 tutoriels rédigés

10 commentaires

Is it possible to remove and change the camera straps for this camera?

stylencreate - Réponse

Yes, after step 8 you will have the back case free then in the inside you will see the latches of the plastic plate that holds the strap, pry them carefully are 6, 2 on each side and 2 in the middle, in the middle of doing it myself have stopped since was no need for that so cannot tell you more.

eportillo5000 - Réponse

Show me how to teardown the flash plz

RAW Fish - Réponse

RAW Fish: Get a terminal driver or other thin device, and wedge it where you can see a line between the outer casing and front panel (where it says “Polaroid” with the rainbow logo). This will need a bit of brute force, but you will be able to seperate a right-angle of outer casing, from the back of the flash, and another right angled bit full of electrics and the front panel. DO NOT touch any of this electrical gubbins - discharging the capacitor through your fingers will HURT. From here you can take out the circuit board and do with it what you wish.

Ariane N -

Hi ! Thanks for your article ! I just bought a Barbie polaroid 600 ;) but unfortunately the flat wire between the camera the flash is disconnected (it dangles from the camera). I managed to remove the flash, that is no longer connected. Do you know how can I open the flash part to reconnect the wires ? Thanks ;)

Marie Dodue - Réponse

Is it possible to reassembly the camera after the teardown?

CameraObscura - Réponse

I just got a cámara however the button for the flash or picture does not work is there a way to repair it ?

Jonathan Gonzalez - Réponse

I have a question are all of the gear supposed to spin smoothly? Or with slight pressure my buck black vision hear on the right side is not moving it on movies when the little silver one on its side moves

Sheila Galvan - Réponse

How do you reassemble the camera? Specifically the metal and bottom part of the film compartment??

Alexis K - Réponse

On step 20, the spring thing, does anyone know its dimensions or where i can buy it? Its missing from my polaroid cam that doesnt work.

Browski -_- - Réponse

Ajouter un commentaire

Nombre de vues :

Dernières 24 heures : 11

7 derniers jours : 60

30 derniers jours : 349

Total : 57,983