Aller au contenu principal

Outils recommandés dans ce démontage

Cette vue éclatée n'est pas un tutoriel de réparation. Pour réparer votre Scotch TL901, utilisez notre manuel de réparation.

  1. The Scotch TL901 Laminator
    • The Scotch TL901 Laminator

  2. Using a small Phillips screwdriver, remove the screws from the bottom of the plastic case.
    • Using a small Phillips screwdriver, remove the screws from the bottom of the plastic case.

    • Rubber feet in the four corners must be removed first to gain access to the screws underneath. A sticker may also be covering the middle screw on the left.

  3. Pull off the silver plastic cover and gain access to the internal components.
    • Pull off the silver plastic cover and gain access to the internal components.

    • The rollers, motor, circuit board, and LEDs are all visible now.

  4. First unplug all three wire headers connected to the circuit board.
    • First unplug all three wire headers connected to the circuit board.

    • Unscrew the two screws holding down the circuit board by its corners and remove the board from the laminator.

  5. Fix Kits pour batterie de MacBook

    À partir de $69.99

    Buy Now

    Fix Kits pour batterie de MacBook

    À partir de $69.99

    Buy Now
  6. Unhook the spring from the plastic surrounding the motor.
    • Unhook the spring from the plastic surrounding the motor.

  7. Hold the roller enclosure from both sides, indicated by the markers, and pull upwards and slightly out.
    • Hold the roller enclosure from both sides, indicated by the markers, and pull upwards and slightly out.

    • Free access to the motor and rollers is now possible.

  8. Remove the motor from the rollers by unscrewing the three screws holding them together.
    • Remove the motor from the rollers by unscrewing the three screws holding them together.

  9. Remove the sensor from the roller enclosure by unscrewing the two spring-loaded screws.
    • Remove the sensor from the roller enclosure by unscrewing the two spring-loaded screws.

  10. Unscrew the two screws and the bar on the other.
    • Unscrew the two screws and the bar on the other.

  11. Pull the black washers sideways off the metal rod of the roller.
    • Pull the black washers sideways off the metal rod of the roller.

    • Pull the gears off.

  12. With the gears off, the plastic panel falls off and the rollers come out of the enclosure. The laminator is now disassembled.
    • With the gears off, the plastic panel falls off and the rollers come out of the enclosure.

    • The laminator is now disassembled.

    Where can you get circuit boards for these

    Brian Stapp - Réponse

Calvin Xu

Membre depuis le 18/04/2013

190 Réputation

1 tutoriel rédigé

Équipe

F14BraunReverseEng Membre de l'équipe F14BraunReverseEng

Community

2 membres

8 tutoriels rédigés

Why is the screw on the left side so hard to get out?

Teri L Geist - Réponse

Thank you..

Putting it back together is more of a challenge.

Frank - Réponse

You're right Frank. For me, getting it to stay together after the tear down and reassembly required superglue and two extra screws. ;) But at least it's working again. Thanks for the great instructions.

pjcall975 - Réponse

Thank you! Just needed to open and remove a jam. Followed your guide and all is well.

KQuinn

Kate Quinn - Réponse

Thank you for posting these instructions. I was able to remove a quarter that got trapped inside.

seanretzloff - Réponse

Thank you! My son fed a sheet in the wrong way and it got completely jammed. Following your instructions, I was able to take the cover off and pull the jammed plastic out. I would NEVER have thought to remove the rubber feet to look for screws!!

Kelly McLean - Réponse

Can you provide instructions on re-assembly? I seem to be lost on the little bar with the hook.

Louanne Trebing - Réponse

I have one with the power cord cut completely off, just behind the machine. Theres not even enough cord left, machine side, to splice it back together. Would removing the plug/cord completely and replacing it with a new one (or the rest of the old one) be an option? Or am i just squat outta luck! Thanks

kkm 0001 - Réponse

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 14

7 derniers jours : 65

30 derniers jours : 208

Total : 17,048