Menu 

Vos paramètres

Mon établi

Accédez rapidement aux tutoriels, aux pièces et aux réponses correspondant à vos appareils
Mon panier (US Store)

On dirait que votre panier est vide

Parcourez notre boutique

Tungsten E Teardown

Rédigé par : Kevin Hom (et 9 autres contributeurs)
Publication : February 4, 2010
  • Commentaires : 2
  • Favoris : 4
  • Affichages : 6.6k

Vue éclatée

Outils recommandés dans ce démontage

Acheter ces outils

Introduction

The following tear down provides a step by step guide to completely disassemble a Palm Tungsten E.

Cette vue éclatée n'est pas un tutoriel de réparation. Pour réparer votre Tungsten E, utilisez notre manuel de réparation.

  1. Remove stylus and SD card. Using T-5 torx driver, remove 4 back panel screws.

    • Remove stylus and SD card.

    • Using T-5 torx driver, remove 4 back panel screws.

    • The screws are small and can be lost easily. Be sure to place them in a secure area.

    Traduire

  2. Begin to remove back cover by inserting the plastic opening tool under the usb and power input slots. Continue by sliding the plastic opener to the right at the markers shown until the cover releases. Continue by sliding the plastic opener to the right at the markers shown until the cover releases.

    • Begin to remove back cover by inserting the plastic opening tool under the usb and power input slots.

    • Continue by sliding the plastic opener to the right at the markers shown until the cover releases.

    Traduire

  3. %Livraison gratuite pour toute commande supérieure à 100,00 $US ou contenant un Pro Tech Toolkit !

    Parcourez notre boutique

    Vous avez déjà réparé quelque chose ? Vous êtes un génie.

    Partagez votre réparation avec le hashtag #ImAGenius

    Nous sommes tous des génies

    Partagez votre réparation avec le hashtag #ImAGenius

  4. Your device may not have a screen protector. If not, you do not need to complete step three. Please move on to step four. Remove screen protector by lifting hinge out of plastic housing.

    • Your device may not have a screen protector. If not, you do not need to complete step three. Please move on to step four.

    • Remove screen protector by lifting hinge out of plastic housing.

    • Remove top cover by gently pulling away from the device with plastic tool

    Traduire

  5. Carefully remove motherboard from the standoffs without damaging the LCD flex connector. Using spudger( the black pencil-like tool shown in picture two), unlock both sides of the flex connector block (shown in the purple boxes in picture two) by pushing down.

    • Carefully remove motherboard from the standoffs without damaging the LCD flex connector.

    • Using spudger( the black pencil-like tool shown in picture two), unlock both sides of the flex connector block (shown in the purple boxes in picture two) by pushing down.

    • Remove motherboard completely.

    • Metal washers may pop out of the device during this step

    Traduire

  6. Remove buttons using fingers. Gently flex frame to release screen from plastic frame. Lift out screen.

    • Remove buttons using fingers.

    • Gently flex frame to release screen from plastic frame.

    • Lift out screen.

    Traduire

  7. Congratulations! You have successfully taken apart a Palm Tungsten E.

    • Congratulations! You have successfully taken apart a Palm Tungsten E.

    Traduire

Auteur

avec 9 autres contributeurs

Kevin Hom

Membre depuis le 21/01/2010

88 Réputation

2 tutoriels rédigés

Badges: 7

+ 4 badges supplémentaires

Équipe

Cal Poly, Team 13-22, Maness Winter 2010 Membre de l'équipe Cal Poly, Team 13-22, Maness Winter 2010

CPSU-MANESS-W10S13G22

4 membres

4 tutoriels rédigés

Un commentaire

Ajouter un commentaire

How does one unplug the battery?

dlcatftwin - Réponse

Voir les statistiques:

Dernières 24 heures : 0

7 derniers jours : 2

30 derniers jours : 17

Total : 6,654