Menu 

Vos paramètres

Mon établi

Accédez rapidement aux tutoriels, aux pièces et aux réponses correspondant à vos appareils
Mon panier (US Store)

On dirait que votre panier est vide

Parcourez notre boutique

Canon EOS 300 Bottom Panel Replacement

Rédigé par : Tammy Kong (et 3 autres contributeurs)
  • Commentaires : 0
  • Favoris : 0

Difficulté

Facile

Étapes

10

Temps nécessaire

10 minutes

Sections

4

Drapeaux

0

Introduction

The bottom panel can be easily removed, and allows access for replacement on other parts of the camera.

Outils

Acheter ces outils

Pièces

Aucune pièce nécessaire.

  1. Open up the battery door. Open up the battery door. Open up the battery door.

    • Open up the battery door.

    Traduire

  2. Remove the batteries from the camera by sliding them out into your palm. Remove the batteries from the camera by sliding them out into your palm.

    • Remove the batteries from the camera by sliding them out into your palm.

    Traduire

  3. Release the side latch to open the back panel. Release the side latch to open the back panel.

    • Release the side latch to open the back panel.

    Traduire

  4. Remove the two black 4.5mm screws above and below the latch. Remove the two black 4.5mm screws above and below the latch.

    • Remove the two black 4.5mm screws above and below the latch.

    Traduire

  5. %Livraison gratuite pour toute commande supérieure à 100,00 $US ou contenant un Pro Tech Toolkit !

    Parcourez notre boutique

    Vous avez déjà réparé quelque chose ? Vous êtes un génie.

    Partagez votre réparation avec le hashtag #ImAGenius

    Nous sommes tous des génies

    Partagez votre réparation avec le hashtag #ImAGenius

  6. Using your finger, carefully pry open the side panel from the top of camera. Pull panel downwards to remove.

    • Using your finger, carefully pry open the side panel from the top of camera.

    • Pull panel downwards to remove.

    • Make sure to keep track of the small black piece of rubber under the latch.

    Traduire

  7. Remove the two silver 6mm Phillips #1 screws. Remove the two silver 6mm Phillips #1 screws.

    • Remove the two silver 6mm Phillips #1 screws.

    Traduire

  8. Flip camera over to the bottom. Remove the one 5mm Phillips #1 silver screw.

    • Flip camera over to the bottom.

    • Remove the one 5mm Phillips #1 silver screw.

    Traduire

  9. Remove the front panel by pulling away from the side with the lever. Remove the front panel by pulling away from the side with the lever.

    • Remove the front panel by pulling away from the side with the lever.

    Traduire

  10. Remove three black 7.3mm Phillips #1 screws located on the corners of the camera. Remove five black 4.8mm Phillips #1 screws.

    • Remove three black 7.3mm Phillips #1 screws located on the corners of the camera.

    • Remove five black 4.8mm Phillips #1 screws.

    Traduire

  11. Simply remove the bottom panel by prying it off with your finger. When removing the panel, be sure the bottom of the camera is facing upright. There are loose gears that may fall out. Be wary of a loose piece of foam attached to the bottom panel.

    • Simply remove the bottom panel by prying it off with your finger.

    • When removing the panel, be sure the bottom of the camera is facing upright. There are loose gears that may fall out.

    • Be wary of a loose piece of foam attached to the bottom panel.

    Traduire
Conclusion

To reassemble your device, follow these instructions in reverse order.

Auteur

avec 3 autres contributeurs

Tammy Kong

Membre depuis le 23/01/2014

643 Réputation

6 tutoriels rédigés

Badges: 11

+ 8 badges supplémentaires

Équipe

Cal Poly, Team 6-20, Maness Winter 2014 Membre de l'équipe Cal Poly, Team 6-20, Maness Winter 2014

CPSU-MANESS-W14S6G20

4 membres

11 tutoriels rédigés

0 commentaires

Ajouter un commentaire
Voir les statistiques:

Dernières 24 heures : 2

7 derniers jours : 3

30 derniers jours : 5

Total : 328