Réparez vos affaires

Droit à la réparation

Boutique

Canon PowerShot SD1400 IS USB Port Replacement

Rédigé par : Faris Rezwan (et 4 autres contributeurs)
  • Commentaires : 0
  • Favoris : 0
  • Réparations terminées : 1

Difficulté

Modérée

Étapes

14

Temps nécessaire

15 - 30 minutes

Sections

1

Drapeaux

0

Introduction

USB Port can be damaged from force exertion on the pins which can prevent it to connect to an external device. This guide will show the steps to replace the USB port in the device.

  1. Remove the four 2mm Phillips #00 screws on both sides of the camera. Remove the four 2mm Phillips #00 screws on both sides of the camera. Remove the four 2mm Phillips #00 screws on both sides of the camera.

    • Remove the four 2mm Phillips #00 screws on both sides of the camera.

    Modifier

  2. Remove the single 4mm Phillips #00 screw from the bottom.

    • Remove the single 4mm Phillips #00 screw from the bottom.

    Modifier

  3. Remove the front face panel off of the camera.

    • Remove the front face panel off of the camera.

    Modifier

  4. Remove the rear panel of the camera.

    • Remove the rear panel of the camera.

    • The user interface panel, side and bottom panel of the camera may fall down by itself while you are taking the rear panel of the camera.

    Modifier

  5. Remove the 3mm Phillips #000 screw from the top of the camera.

    • Remove the 3mm Phillips #000 screw from the top of the camera.

    Modifier

  7. Pry the golden ribbon cable from the motherboard with a plastic opening tool.

    • Pry the golden ribbon cable from the motherboard with a plastic opening tool.

    • A screw will be visible underneath the golden ribbon after prying it.

    Modifier

  8. Remove the 3mm Phillips #000 screw from the motherboard.

    • Remove the 3mm Phillips #000 screw from the motherboard.

    Modifier

  9. Use a plastic opening tool to flip up the retaining flap on the ribbon cable ZIF socket.

    • Use a plastic opening tool to flip up the retaining flap on the ribbon cable ZIF socket.

    Modifier

  10. Unplug the small chip from the face of the camera using a pair of tweezers. Unplug the small chip from the face of the camera using a pair of tweezers.

    • Unplug the small chip from the face of the camera using a pair of tweezers.

    Modifier

  11. Remove the 3mm Phillips #000 screw from the rear face of the camera.

    • Remove the 3mm Phillips #000 screw from the rear face of the camera.

    Modifier

  12. Remove the top panel from the camera.

    • Remove the top panel from the camera.

    Modifier

  13. Pry the golden ribbon cable attached to the USB port using a plastic opening tool.

    • Pry the golden ribbon cable attached to the USB port using a plastic opening tool.

    Modifier

  14. Remove the 3mm Phillips #000 screw located at the top right of the USB port.

    • Remove the 3mm Phillips #000 screw located at the top right of the USB port.

    Modifier

  15. Remove the USB port. Remove the USB port.

    • Remove the USB port.

    Modifier
Conclusion

To reassemble your device, follow these instructions in reverse order.

Une autre personne a terminé cette réparation.

Auteur

avec 4 autres contributeurs

Faris Rezwan

Membre depuis le 21/05/2018

457 Réputation

2 tutoriels rédigés

Badges: 5

+ 2 badges supplémentaires

Équipe

IUPUI, Team S1-G2, Harley Spring 2018 Membre de l'équipe IUPUI, Team S1-G2, Harley Spring 2018

IUPUI-HARLEY-S18S1G2

7 membres

4 tutoriels rédigés

0 commentaires

Ajouter un commentaire

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 0

7 derniers jours : 0

30 derniers jours : 1

Total : 170