Introduction

This guide will explain how to replace the .440 and 11 Amp fuses. Both fuses can be removed and replaced the same way, so either one can be replaced using this guide. Remember to put the each fuse in its correct socket based on its current rating. To make sure that your replacement fuses are compatible with the Fluke 77 Series III Multimeter, refer to the back panel fuse rating label or the Service Manual.

Pièces

Aucune pièce nécessaire.

  1. Be sure any test leads are out and the multimeter is off before opening the device.
    • Be sure any test leads are out and the multimeter is off before opening the device.

    • Turn the multimeter so it is display side down.

    • Lift up the back stand of the device by putting your thumb in the curved well at the bottom of the device, so you have access to the two covered screws below.

    Ajouter un commentaire

  2. Use your Phillips #2 Screwdriver to remove the four black 21 mm Phillips #2 screws.
    • Use your Phillips #2 Screwdriver to remove the four black 21 mm Phillips #2 screws.

    Ajouter un commentaire

    • Turn the Fluke 77 Series III Multimeter back over so that it is display side up.

    • Pry the front panel from the back panel at the seam.

    • If the front panel does not come off easily, move a plastic opening tool along the seam until the panels separate completely.

    Ajouter un commentaire

  3. Répandez la magie de Noël
    Obtenez 12 $ de réduction sur les commandes de 50 $ ou plus avec le code FIXMAS12
    Répandez la magie de Noël
    Obtenez 12 $ de réduction sur les commandes de 50 $ ou plus avec le code FIXMAS12
    • When doing this next step, make sure to remove the battery slowly, so you don't damage the wires connecting the battery to the device.

    • Locate the 9V battery in the lower right corner of the device.

    • Pull the battery out of its terminal.

    Ajouter un commentaire

    • Only pull on the metal snaps and battery. Pulling the cords may damage them.

    • Detach the two metal snaps from the battery.

    Ajouter un commentaire

    • Replace a fuse only with a fuse identical in type, voltage rating, and current rating as specified by the back panel fuse rating label or the Fluke 77 Series III Service Manual. Inserting the wrong replacement fuse could create a fire hazard.

    • Locate the fuses near the bottom left corner inside the device.

      • Take note of which fuses belong in which location before removal. They are NOT interchangeable.

      • The .440 Amp fuse is located in the upper left hand fuse holder.

      • The 11 Amp fuse is located in the lower right hand fuse holder.

    • Lift the rounded edge of the fuse with one finger until that side is completely out of its holder.

    Ajouter un commentaire

    • Grab the lifted edge of the fuse between your thumb and forefinger and pull it the rest of the way out of the device.

    • The fuse in the upper left corner can be tricky to remove. Use a plastic opening tool if needed.

    • Repeat steps 4 and 5 to remove the other fuse if you are replacing both fuses or if you are replacing a different part further on.

    Ajouter un commentaire

Conclusion

To reassemble your device, follow these instructions in reverse order.

2 autre(s) ont terminé cette réparation.

Jessica Bombardier Shaw

Membre depuis le 29/01/2014

961 Réputation

7 tutoriels rédigés

Équipe

Cal Poly, Team 2-10, Amido Winter 2014 Membre de l'équipe Cal Poly, Team 2-10, Amido Winter 2014

CPSU-AMIDO-W14S2G10

4 membres

10 tutoriels rédigés

Its not that fuse but one like it on the main board in the stereo

Jennie Walters - Réponse

Ajouter un commentaire

Voir les statistiques:

Dernières 24 heures : 2

7 derniers jours : 18

30 derniers jours : 60

Total : 2,613