Aller au contenu principal

Réparez vos affaires

Droit à la réparation

Boutique

Introduction

Cheap fog machines are often damaged because of their poor quality. Most of this damage can be easily repaired. This guide can be used to repair many common problems that can be encountered when dealing with this type of fog machine.

The fog machine I repaired is called 'eurolite n-19', but it is also sold under other names.

Pièces

Aucune pièce spécifiée.

  1. Open the fog machine by removing the screws on the sides of the fog machine with the appropriate screwdriver.
    • Open the fog machine by removing the screws on the sides of the fog machine with the appropriate screwdriver.

    • Remove the outer casing of the fog machine.

  2. If the fog machine does not heat up, a fuse or another heating element could be malfunctioning.
    • If the fog machine does not heat up, a fuse or another heating element could be malfunctioning.

    • If no smoke is coming out of the fog machine, then the pump could be malfunctioning

    Link is spam. (As you may have guessed after reading this far, the author isn't actually trying to help you fix your machine.) Don't click the link to the guide.

    Daniel Jackson - Réponse

  3. OUVRIR TOUS LES ONGLETS

    Kits de mise à jour de RAM pour Mac

    Voir les kits

    Assez de RAM
    pour ouvrir tous les onglets

    Voir les kits
  4. In this instance, all that was needed was a new heat fuse and new spade connectors
    • In this instance, all that was needed was a new heat fuse and new spade connectors

    • In this case, I needed to remove the heat fuse and the spade connectors then needed to connect the new heat fuse and spade connectors to their respective locations

    • The heat fuse sits under the bimetal. (Cannot be seen clearly in the picture)

  5. To reassemble your machine, follow the steps for diassembly in reverse order.
    • To reassemble your machine, follow the steps for diassembly in reverse order.

    Where did you find the parts? (Heat fuse)

    Todd Maxwell - Réponse

Conclusion

To reassemble your device, follow these instructions in reverse order.

5 autre(s) ont terminé cette réparation.

rjay

Membre depuis le 29/09/2012

215 Réputation

1 tutoriel rédigé

14 commentaires

My fogger heater is jam how can I clean it?

vishal_kishor777 - Réponse

hmm… I think I could have written a better guide myself. Okay so I have a 3 pin XLR for phase does anyone know how this works also I noted that the fuse was melted into its holster and the pump seems dead. My Fogger also has some kind of potentiometer which controls the heating element which is like a ceramic sandwich and two spark plugs… I also was wondering if glycerin fog juice can be made with vegetable glycerin or the glycol type or if this is what cloggs the machine. Also will clr work or be dangerous fume wise? Can you market glycerine as fog juice thickener like STP fuel additives for cars?? g0pg.xyz is my website you can learn how to force push graphite if you look for the post with yoda!

Ember Leona - Réponse

Where can I buy a fuse like this? Have looked over the net, but could not find any shops that would sell CH-15 fuse, used in this fog machine. If anyone knows about this, please share info. Thanks! By the way, I’m based in EU.

Giedrius Stasiulis - Réponse

I would make a post on Halloweenform.com

Mad_as_a_hatter -

My fog machine is not pumping out smoke

Ohwaga Kerry - Réponse

Have you cleaned your machine?

Mad_as_a_hatter -

No power to my fog machine ?

David McCartie - Réponse

Thw machine doesn't power on at all? Dose it get hot ? If it not getting hot. Check the fuse. If you hear the pump trying to work and nothing comes out. You would need to use fog cleaner or water and white vinegar.

Mad_as_a_hatter -

My FM400-1 fog machine pumps out fog for 1 minute then stops, cools and then pumps out fog for another minute then stops again. Is this normal or is the safety device wearing out?

Paul Houle - Réponse

Yeah that would be normal for a 400 watt fog machine. The heating element has to be 200 to 250 degrees. When pumping fog it will cool it down. The heating element needs to reheat up again. Before it will pump more fog.

Mad_as_a_hatter -

My fumigation machine is not fuming out smoke

MANMEET KHALSA - Réponse

Have you cleaned your machine? You can fog cleaner or you can use water and white vinegar.

Mad_as_a_hatter -

Can we use 900W coil instead of 1500W coil in a machine

Rajendra Katote - Réponse

Just guessing I would say not. Depends on the model and the watts you would want to find a similar replacement. You could even find a broken fog machine to use as parts

Mad_as_a_hatter -

Ajouter un commentaire

Afficher les statistiques:

Dernières 24 heures : 12

7 derniers jours : 75

30 derniers jours : 336

Total : 49,373