Cette version peut contenir des modifications incorrectes. Passez au dernier aperçu vérifié.
Ce dont vous avez besoin
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove both end caps by putting a plastic opening tool in the center of the seam. Work around the edges to pry the end caps off completely.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the Jambox upside down. Peel the indicated rubber tabs off, using a plastic opening tool if necessary.
-
Remove the three T6, 7.0 mm screws under each rubber tab.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
With the Jawbone logo facing towards you and with correct orientation, place the Jambox with the left end cap facing upward.
-
Unscrew indicated T6 9.7 mm screws.
-
Gently loosen the tabs from their anchor points so the bottom may be removed.
-
Flip the Jambox so the other end cap is facing up. The USB cable is on this side (metal grounding clip, indicated in orange). Repeat the above two steps.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Pry up the bottom panel by lifting from the device.
-
Pull the bottom up. This may take a bit of force as the bottom is glued to device.
-
Once removed, the battery will now be visible.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Unscrew the eight indicated T6 9.8 mm screws. Remove metal grounding plates.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Once all eight screws are removed, pry the sides of the Jambox to lift the body from it's shell.
-
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
With the battery facing forward, remove the three indicated T6 9.5 mm screws.
-
Once the screws are removed, lift up the small plastic plate, revealing the auxiliary board underneath.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Turn the Jambox so that the button panel is visible.
-
Remove the indicated screws, T6 9.6 mm.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the colored ribbon that connects the green button circuit board to the blue auxiliary board by using your finger to lift the small black tabs that clamp down the ribbon.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Place the disassembled Jambox with the speakers facing up.
-
Locate the screws around the broken speaker.
-
Use a T15 screwdriver to remove the four 12.1 mm screws around the broken speaker.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Using a plastic opening tool, pry the speaker out of the Jambox.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Desolder the wires from the speaker terminal in the Jambox.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the two PH0, 5.8 mm screws on the small plastic black panel using a screwdriver.
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Remove the four T6, 9.9mm screws that secure the button circuit board to the body
-
-
Cette étape n’est pas traduite. Aidez à la traduire
-
Minding the small L-shaped piece of metal on the end opposite of the ports, lift the circuit board from the body of the Big Jambox.
-
Annulation : je n'ai pas terminé ce tutoriel.
3 autres ont terminé cette réparation.